Search results

  1. MickLovin

    Tilt Trim issue - 1994 Force 120

    Re: Tilt Trim issue - 1994 Force 120 Is this the trim ram you are referring to, this ram is your trim ram and the other is your tilt ram which is the skinny one, the tilt ram when going up comes into play after the trim ram slowly trims up enough for the tilt ram and same when it comes down...
  2. MickLovin

    Chrysler 100HP tilt ram repair

    Hi guys sorry to ask so many questions, but if I don't ask, I don't learn, so you have to put up with me :P. Ok I have a kit for my tilt ram and trim ram, I have lifted my motor to 1 inch above bottom of keel as I felt the motor was heavier than my 75hp and because of my 20 gallon tank ( Amercan...
  3. MickLovin

    Low voltage on hummingbird and loud ping with Chrysler motor - resolved

    Hi guys, Just thought I would give you an update of the problem I had come across. I was getting a ping when I went down to neutral from forward also a low voltage reading on my fish-finder, but the low voltage reading only came up when I was at idle. I played with the gear cables and lever and...
  4. MickLovin

    new used boat owner

    Re: new used boat owner Your wiring harness should have red = + battery/ignition 12v, black = ground, white = tacho, purple = generator which isn't connected at switch, green = choke, orange = warning buzzer negative - from the motor with the positive + coming from your ignition switch on with...
  5. MickLovin

    Hummingbird tranducer casuing spray

    Hi, I am not sure if this is the right forum but I have a problem with my Hummingbird transducer causing too much spray at the back of my boat to the point it is spraying in, it doesn't matter where I mount it it still causes a spray. I have mounted it as per the instructions. Am I better with a...
  6. MickLovin

    Loud ping when putting back from forward to neutral

    I took my 100HP outboard out for a water test after putting the new TC carbs on it. when I would idle back and then go to neutral it would let out a loud ping once, I would put it back to forward then back to neutral and a ping, but not every time. The motor did its hole shot fine and was...
  7. MickLovin

    Force 9.9 water pump impeller change

    Re: Force 9.9 water pump impeller change Easy as, like you I don't understand why marine mechanics think they can charge you an hours labour when it takes 15 minutes for this job. If you have done one before, this will be a piece of cake. The only thing I found when I did mine ids that I had to...
  8. MickLovin

    new used boat owner

    Re: new used boat owner I was under the understanding he had no ignition switch, so I was advising how I did it with a harness to my 75hp when I had it on a stand, for starting purposes only as I had my ignition switch on the boat which had the 100hp on it. It was a suggestion to see if he...
  9. MickLovin

    new used boat owner

    Re: new used boat owner Well that is your problem, you need power to be on the blue wire which it gets from the ignition switch, So you turn your ignition to on and it supplies power to blue, you turn your ignition to start and it supplies power to yellow. You can manually operate the choke...
  10. MickLovin

    new used boat owner

    Re: new used boat owner Take the throttle and gear cable controls off the motor inside, make sure all your electrical connections are correct as in they normally have a colour code reference on the side of the motor, negative is normally last and the negative from the battery is bolted on...
  11. MickLovin

    Home made trim tab on motor make sense?

    Re: Home made trim tab on motor make sense? What pnwboat said, it's a snout which you probably just need to move to centre or if it is centre try turning the front of the snout as you are looking at it to the left to compensate for it pulling right.
  12. MickLovin

    Fuel filter yes or no

    Re: Fuel filter yes or no With my Chrysler I used a right angle filter which I cable tied to the hose between the flanges for the carbies, I have also put clear fuel line in between the fuel pump and carbies and between the carbies, as long as the filter doesn't restrict flow I can't see why...
  13. MickLovin

    Chrysler 100HP tilt trim sender

    Hi guys, I have a tilt trim gauge that I picked up from a bloke parting his Chrysler, unfortunately the sender unit was broken when he attempted to get it off the motor. They seem to be rare as hens teeth, could I use a mercury or force sender unit, or won't this work with my Chrysler gauge.
  14. MickLovin

    Recirculating system on 100HP Chrysler and puddle drain

    Just as a matter of curiosity, what can you check when you look at the recirculating system with a 100HP Chrysler, I heard if it cause problems with the puddle drain??. I haven't water tested my 100HP yet, but have the carbies synced and ready for water test, but I have noticed wet plugs when...
  15. MickLovin

    Prepping and painting a 1980's half cabin

    Hi all firstly I will apologise if I have put this in the wrong category, I have a 17ft half cabin which I have just given a one pack coat of black gloos enamel to the bottom after hours of stripping the original terrible paint job with 3 different coats of paint to get through. After 2 days of...
  16. MickLovin

    Help Frank :) - 100HP Chrysler carburettor change from wb24B to TC5D

    Re: Help Frank :) - 100HP Chrysler carburettor change from wb24B to TC5D just posting some pics of the carbs on and the covers
  17. MickLovin

    6hp Chrysler Model 64HD

    Hi guys, I got a old Chrysler 1978 model 64H8D, it has spark but doesn't start or even suspect to fire. I put br6hs plugs in and checked for spark, which I have, I took apart the carbie to make sure there was no crap in it. I may need new fule though as I am using my spare tank, but I would of...
  18. MickLovin

    Installing a temperature gauge worth it or not

    HI again, sorry to ask so many questions, but is it worth putting a temp. gauge on my Chrysler outboard, I know the buzzer definately works but not sure if the sender works or how to test it, does it have an Ohm reading? Every time I have tried to either put a tell tale in or a sender into the...
  19. MickLovin

    Chrysler 100HP Purple charging/signal wire for Ammeter??

    Re: Chrysler 100HP Purple charging/signal wire for Ammeter?? this look right? basically not the same motor but ammeter wiring should be same?
  20. MickLovin

    82 35hp chrysler wiring help please

    Re: 82 35hp chrysler wiring help please And this is your 35hp 1982 I believe...
Top