Search results

  1. M

    finding tdc for timing

    Thanks for your input ... helped alot apparently I was way off on the whole .462 idea...
  2. M

    finding tdc for timing

    I have a 200 hp off shore carbureted engine SN 0G693618 . The boat is new to me and its not idling correctly. I know the P/O was a tinker because when I mentioned it he said you just have to adjust this screw a little and pointed to the max spark advance screw ... so before I go messing with...
  3. M

    Power Trim issue

    loosen the bypass on the right hand side enough to push motor all way up then tighten it back up add fluid then lower engine with the pump and repeat until you can get the trim to raise the motor with out issue's
  4. M

    Roller bunk Adjustment advise ...

    It's a magic loader by magic tilt ... as far as something missing are you talking about on the circled bolts below? If so those bolts have to be lose to allow for the wobble rollers to move with the bottom of boat ...
  5. M

    Roller bunk Adjustment advise ...

    Ok thanks for the clarification...and yes I can get the boat off the rollers ...
  6. M

    Roller bunk Adjustment advise ...

    Here's a few more pictures these are the front rollers that need to be moved to get them off the strikes. In moving them outward this means away from the keel correct? Im just asking because that would put them towards the outside of the hull. some better pictures might help
  7. M

    Roller bunk Adjustment advise ...

    Yes the keel has about 10 inches.. and the back of the roller is even with the transom on the starboard side but the front of the boat is not centered in the trailer so I'm hoping that once I get it centered it will move that side back a little on the trailer.. if not I have room to move the...
  8. M

    Roller bunk Adjustment advise ...

    Looking for advise for roller bunk adjustment... in the pictures bellow you can see that I need to adjust the rollers on this trailer.. My question is should I move the bunks so that they are straddling only the 1 strike closest to the keel or should I spread the rollers apart and have them...
  9. M

    Trim O-rings

    I would love to find it for that
  10. M

    1987 150 xr2 trim tilt bleeding

    let me know how it goes I have been fighting this issue after I replaced the motor on mine here is a video of what mine is doing
  11. M

    Trim O-rings

    Lol its 109.00 for what you see in the picture
  12. M

    Trim O-rings

    Is there anywhere I can get O-rings for the trim system with out paying mercury's inflated prices S/N 0B143346 Thanks Mark
  13. M

    Gel coat damage on transom

    yeah the transom is solid and dry I even sealed from the inside and pulled a vacuum for days on each hole just to see if I could pull any moisture out and got nothing. now the boat spent its life in the water at a dock so I'm sure some moisture got in but the holes was dry....
  14. M

    Gel coat damage on transom

    Any Ideas for a repair
  15. M

    Gel coat damage on transom

  16. M

    Gel coat damage on transom

    Every thing I have read says no silicone ... use 3m 4200 I thought I was doing the right thing 🤦‍♂️🤦‍♂️
  17. M

    Gel coat damage on transom

    Ok I will get my son to send me a picture
  18. M

    Gel coat damage on transom

    So I pull my 200hp motor off to replace the mounts and trim pump on a 91 wellcraft boat I just purchased I reinstalled the motor on sunday ( using 3m 4200 ) just to find out that the trim wont go alway down so I had to remove motor again to remove the trim assembly but I only removed 1 of the...
  19. M

    200 hp trim problems

    I have a 98 200hp that I bought with no trim motor on the pump I bought a new trim motor and pump assembly and the trim goes up and down but when it gets to the trim rods it acts like it's all way down down and sounds like its under alot of pressure... not sure what to check. Here is a video...
  20. M

    Sierra Upper mounts

    So I received the second mount today and it is a composite/plastic mount also so Im guessing that is the way its supposed to be...
Top