Search results

  1. M

    Water from 3.0L mercruiser

    Is that the bottom of the manifold?
  2. M

    No water out transom or exhaust

    You wont have impeller damage if you have water at the impeller..... remove the small hose coming from the transom that is the water from the impeller point it down in the bilge start turn muffs on and start the boat and make sure you have plenty of flow from the impeller...
  3. M

    Desperate at this point. Alpha one please take a look.

    Stop do not attempt to start until you get the shifting problem fixed. If the shifter is in a bind and prop is clicking both ways you could eat your lower unit up if you continue...
  4. M

    Mercruiser 3.0 Rebuild or not

    It wasn't just in the valve cover.... I noticed the milky oil on top of valve cover making me think blow by because oil was on top the entire oil pan was full of milky oil so I changed the oil and took it out the next day and it was milky after 1 hour run... but I believe that was because of...
  5. M

    Mercruiser 3.0 Rebuild or not

    I have a mercruiser 3.0 I have been fighting issues with idling . I replaced the carb didnt fix the problem then I noticed that I had milky oil puddled on valve cover so I assumed I had a cracked block. I removed the elbow and found that the elbow is bad so that may be the problem with the water...
  6. M

    MerCruiser 3.0 to Omc 4.3 swop

    Well back in November I bought a 1990 Wellcraft fish20 with A 200hp Mercury I've had the boat out twice and now its for sell lol it takes about 20 gallons of fuel to do what I normally do with about 11 gallons in the sea pro with the 3.0 ...
  7. M

    MerCruiser 3.0 to Omc 4.3 swop

    I have a Cobra on 1 of my other boats Its ok but not a Mercruiser .. I am aware of the that I would have to take everything from 1 boat and put in the other boat along with glassing in new mount pads.. I just wanted to see what the thoughts where and would I pick up any speed with the 4.3 over...
  8. M

    MerCruiser 3.0 to Omc 4.3 swop

    I have a 20 ft sea pro Duel Console with a Mercruiser 3.0 the engine has been given me problems idling so I bought a new carburetor that did not fix the problem then I noticed oil around the top of engine from blow by so I did a leak down test and I'm losing 40 psi give are take on every...
  9. M

    200 hp trim problems

    yeah it was a bad pump they sent me a new one
  10. M

    No power tilt and nothing happens when I turn the key

    Did you check the fuse on the motor ? its normally above the starter solenoid that sends power back to the switch
  11. M

    Mercury 110 9.8 cylinder numbering

    Top Number 1 always closes to the flywheel
  12. M

    gear shift removal

    Mine did not need to be disengaged to remove button !! it just popped right off ... Maybe it was a fluke
  13. M

    gear shift removal

    First you remove bottom in center of handle " The throttle only button" Then remove throttle control with a socket after that you pry the cover shield off " the one that says quicksilver 3000" The screws for removing will be behind that cover !!!
  14. M

    2003 150 saltwalter water pump tube

    No problem glad to help!!
  15. M

    Power Trim issue

    yes my motor and pump are a set so the company sent me new motor and pump I still believe your system is low with air in it
  16. M

    2003 150 saltwalter water pump tube

    What's circled in red is the items in your picture
  17. M

    2003 150 saltwalter water pump tube

    Yes water tube bare copper . The rubber seal goes into the water pump housing and the plastic tube is a guide for the water tube
  18. M

    Power Trim issue

    I was referring to the $50 its like $109 and that only does them pump and trim rams not the main cylinder... Mine would do everything it was supposed to do except when it hit the 2 trim rams it would stop like it was hitting A brick wall instead of going completely down
  19. M

    Power Trim issue

    I just went through an issue with my trim after replacing the pump motor and I rebuilt my system and I can assure you that you will not fine a complete kit for $50.00 ... see my thread https://forums.iboats.com/threads/trim-o-rings.741946/ my issue ended up being the new pump that came with the...
  20. M

    finding tdc for timing

    That makes all the since in the world no rocking....
Top