Search results

  1. A

    StarCraft 181 SS conversion

    If properly done, the plywood transom would outlive you ! My 1983 Islanders transom lasted for almost 40 years and back then nothing was treated, just plain marine grade plywood. What are the chances of you still owning that boat in 40 years ? Definitely not worth the cost of aluminum.
  2. A

    Which kicker mount to install?

    While not easy, some how you need to access the underside of that flat surface as that would be the easiest area to attach a mount. One could be adapted to the actual stern, but access to that would be even more dificult. Perhaps contact the boat mtg and see what recomendations they might...
  3. A

    Stripped drain plug

    Is it a bronze plug ? If so, re tap the hole a size larger if threads are totally gone, the n get a bigger plug if there is enough room to go bigger. Often times just the first few threads are bad, if that is the case fetal the female half to clean up the current threads and go with a longer...
  4. A

    Boat Cover Repair?

    Can't remember the name ( heck, can't remember my own) but there is a product for repairing tents, a glue on patch product that I have used in years back. Not sure if it is still on the market or not. Comes with a piece of patch material and glue that holds ( or used to hold) really well. The...
  5. A

    Pushing Run-Flat tires to the limit

    Many laws are not enforced by police, and that is a big cause of road rage ! Another big issue is keeping right except to pass. A law here in Ohio but very rare anyone is pulled over for it. Another is the 45 mph minimum speed on our 60-65 mph speed limit on out local expressway system. Often...
  6. A

    Stuck floor board over gas tank on Alumacraft

    Perhaps you missed some fasteners, those buried in carpet are hard to find.
  7. A

    Is my motor sitting to low?

    Didn't catch the pontoon part....way different than a boat !
  8. A

    ‘91 merc 60hp hitting wot rpm??

    Before spending money, is the motor performing at its peak ? Make sure carbs are wide open. Buy a cheap portable tech and see if your tech reads correctly. If you spend money on props and later find the motor was not operating correctly, you will need to start over. What boat, how much...
  9. A

    Is my motor sitting to low?

    Can't tell much from the pics....
  10. A

    Boat Cover Repair?

    While it won't be pretty, get a piece of heavy fabric and some flexible water proof glue. Glue a patch to cover the tear and spread the glue on the outside as well. Made many crude patches over the years and they last, they just look ugly. If appearance is important, see your local canvass...
  11. A

    Trailer Set Up

    That front roller is doing nothing but get in the way. I would add a couple keel rollers to the crossmembers, I am a believer in extra rollers rather to few. If n 60 plus years of boating, never dented an aluminum hull from rollers ! Adjust your winch stand however to get a straight pull...
  12. A

    Trailer tires.

    You make a good point on the long trips. I haven't had any tire issues either, but most of my trips are under 25-30 miles each way. Long hard highway miles can create some big heat buildup, and that will defiantly test your tires!
  13. A

    How to kill mold on billge/engine surfaces

    I don't like it either, but the smell seems to disappear quickly. I pour a little in the sink and wipe the counter top after cleaning fish. Wife comes in a half hour later and can't smell it....works for me that way. We have a lot if those little fruit fly type bugs. They hang out in the...
  14. A

    How to kill mold on billge/engine surfaces

    We have that available as well, but much harder to find. Most grocery stores carry the 6%, so readily availiable. Some of the farm stores carry the higher acidity stuff but not always.
  15. A

    How to kill mold on billge/engine surfaces

    I spray it on full strength and heavy, let sit overnite. If mold is heavy I will use a brush to loosen it up, rinse and repeat. The acid of the vinegar kills the mold, also works great on bugs!
  16. A

    Trailer tires.

    Looking back over 60 plus years of trailer towing of various size trailers I can only recall two times I had tire issues. Then again, I keep close tabs on my tires ! Anyone can have a bad batch if tires, not uncommon at all. Most tires will give clues when they begin to fail, but most folks...
  17. A

    How to kill mold on billge/engine surfaces

    Sheesh.....simple and cheap cleaning vinegar works wonders and safe to use. With all the rain and extreme temp swings we have been having some mold issues. A spray bottle with 6% cleaning vinegar gets sprayed onto the mold and next day it is gone. Wipe off or spray off, depending the surface...
  18. A

    Lower Unit Oil Leak

    Would be kinda unusual for gear oil to be above the cav plate....Have you checked the gear case oil for water intrusion or low level ?
  19. A

    OK a question. I have a little 1984 Evinrude 7.5 HP.. Beautiful motor.

    My main motor is a long shaft and my kicker is a short shaft. The transom cutout is wide enough that the kickers clamped on the cutout same as main motor. While under way with the kicker, there is plenty of water over the cav plate to keep it pumping without issues ! If it were up on plane...
  20. A

    type and color of paint of Starcraft Islander.

    Good for you, most folks balk about spending a few extra bucks on their boats when it comes to paint and other decorative things. We enjoy helping people spend their money, so will be watching to see you spending a bunch...lol...
Top