Search results

  1. jimmbo

    Mercury 50hp thunderbolt 1974

    Is the Distributor rotating as you move the Throttle Linkage?
  2. jimmbo

    Will a Merc '77 IL6 gearcase fit a '93 Merc V6

    When Mercury was designing the V6 in the early 1970s, they did use the I6 Gearcase and Midsection, however that was for the Prototypes, using Driveshafts that were unique for the Prototypes Here are few pics of Old Blue, the 1st V6 Prototype, using an I6 midsection and gearcase, First pic is...
  3. jimmbo

    Mercury 50hp thunderbolt 1974

    When you say "set the primary timing 8' btdc, set the wot 35' " Did you mean the Primary Pickup Timing at 8' btdc? That is where the Advance should be when the Carbs are just opening the tiniest bit, and I mean tiny, from being fully closed. It is not an Idle speed Timing Spec Are you using a...
  4. jimmbo

    1974ish Johnson 70hp powershift 2 question.

    Well, like any Electronic Ignition System, it is reliable until it quits working. Keep in mind it is 50+ yrs old, and replacement parts can be difficult to find. While the earlier versions of this Motor did have Points(still Electronic though), by 74 they were Breakerless. There are 3 carbs...
  5. jimmbo

    Mercury Tempest, Turning Point Mach 3 or Michigan Wheel Apollo?

    If you go back and read the reviews and comparisons carefully, they weren't exactly on the Up and Up. They certainly didn't make sure the Props being used for comparison to were setup for best Performance. When I read them, I thought I was reading a Paid Promotion, kind of like an Infomercial
  6. jimmbo

    1974ish Johnson 70hp powershift 2 question.

    It is 50+ yrs old. They were good engines in their day, and were quite versatile, and offered good Fuel Economy. Were they Perfect? No, they had their share of Problems. They were producing almost 1 1/2hp per cubic inch, and propping was critical if you wanted a long engine life as overpropping...
  7. jimmbo

    Mercury Tempest, Turning Point Mach 3 or Michigan Wheel Apollo?

    Sharrow Paperweight is likely more accurate
  8. jimmbo

    Mercury Tempest, Turning Point Mach 3 or Michigan Wheel Apollo?

    The RAKER is a Good Prop, the Enteria is Better. RAKER was introduced in 1985 and the Enertia in 2005. Props haven't changed much since, though was some goofy looking thing a few year ago, that a couple of people on this Board were tripping over their Tongues about, but it has NEVER been...
  9. jimmbo

    Mercury Tempest, Turning Point Mach 3 or Michigan Wheel Apollo?

    No, I was running an OMC RAKER in the Pics of Boat moving. The Black Prop was the AL Prop that came with the Boat. I still have it as a Spare Here are my 3 SS Props. In the Center is the Enertia, the others are RAKERs
  10. jimmbo

    Just thought I'd share a nice photo.

    His Loyalty will NEVER questioned/doubted
  11. jimmbo

    Mercury Tempest, Turning Point Mach 3 or Michigan Wheel Apollo?

    5.7. It wasn't offered with the 5.7 but rather with a 5.0 with EFI(horsepower was the same as a 5.7 with a 2bbl Carb), but still, it came out of the Factory with the 5.7(I think there were 6 or 7 of them, used at a Dealer Convention/Show). Wouldn't want anything smaller in it. It has enough...
  12. jimmbo

    Mercury Tempest, Turning Point Mach 3 or Michigan Wheel Apollo?

    That Hull doesn't have a Pad. I was taking the Picture, my Cousin was in the Boat
  13. jimmbo

    Mercury Tempest, Turning Point Mach 3 or Michigan Wheel Apollo?

    I highly recommend the Mercury Enertia. Been running one for over 20 yrs, prior to it I was running an OMC RAKER. The Enertia, lifts the entire Hull vertically, and still gives good Bow Lift. The Outdrive is not producing a Roostertail, so I am not over trimming
  14. jimmbo

    SNOW Common Sense

    It was a 76 Olds 88 Royale, It had the 455 with a Turbo Hydramatic 400. 2.56 Rearend. I had the 4dr Hardtop, the old Man had the 4dr Sedan
  15. jimmbo

    SNOW Common Sense

    This was one nights' snowfall in April of 85. Motor was running when I took the pic. Drove it out of there about 20 minutes later. One Wheel Drive, with 1980's Winter Tires on the rear
  16. jimmbo

    Getting impatient

    I've been counting the Days till Spring since Sept
  17. jimmbo

    90 Mercury 40HP motor

    If that motor has Power Trim, it has Power Tilt.
  18. jimmbo

    2020 DF35A 30hp conversion.

    An increase in Horsepower from any given Displacement, requires raising the Rpm at which the Hp is attained by shifting the Torque Curve Upward, which 95 out of 100 times results in weaker Low Rpm Torque. Repropping, with a lower Pitch will hide some of that, and allows the engine to operate in...
  19. jimmbo

    2020 DF35A 30hp conversion.

    A gain of about 1 mph
  20. jimmbo

    New Stuff on Vehicles likes/dislikes

    I can adjust the Level of Heat when it is on, but I can't adjust the Temp at which it turns On, which is about 10C(50F)
Top