Search results

  1. B

    what pitch do i want?

    my lund tyee 1850 with merc 4.3 lx has a 21 pitch prop, and i can only get 4400 rpm out of it.( so far) my cavitation plate is broken and currently getting fixed. after its back, what rpm should i be getting at wot? is it really bad if i'm not getting what i should, but more than happy with the...
  2. B

    running too cold??

    just got my boat together last week. took it out on the river, and it ran great. except that it would not get over 110 degrees. or at least according to the gauge. changed to new sending unit, same problem. when i ground the wire, it pins the gauge over. 96 merc 4.3lx. i have two sending units...
  3. B

    how long can i run on muffs?

    how long can i run my boat(96 4.3 merc) on the muffs? i need to break it in, and it's supposed to be windy as hell tomorrow, and the river still movin' pretty good. was hoping an hour of idle up to maybe 1500. is this okay, or is it only idle on muffs?
  4. B

    distributor orientation 4.3 merc

    where does the #1 terminal point on the distributor? took mine out a few months ago, and can't remember it's orientation. i have the piston at tdc, and will time the engine after it's running,but want to know what position to put the dist. in. thanks. pics would help if available.
  5. B

    priming oil

    96 4.3 std rot. which way do i spin the oil drive to prime to oil system when first firing a new engine?
  6. B

    what plugs??

    i've got a 96 merc 4.3, which i have changed to one from a 90 jimmy. what plugs should i use for this set up? not sure if the automotive ones would be the same as marine. i'm using the ignition from the 96, but the motor is a 90.
  7. B

    shift cable thread?

    anybody khow what tap i need to clean up thhe threads for the lower shift cable on alpha1 gen2? specifically where it goes thruogh the bell housing.
  8. B

    shift boot clamp?

    how tight should the crimp pclamp be on alpha one gen 2? is the cable supposed to be able to slide in and out when the outdrive goes up and down?, or is this the reason for the bellows?
  9. B

    seal part #

    can anybody tell me what part number the seal behind the gimbal bearing is? it is a alpha one gen 2 out drive.
  10. B

    reason for marine head gaskets?

    i'm going to use a truck motor in my boat, and i ve always heard i need marine head gaskets and brass welsh plugs. If my boat will never see salt water, is this still required, and what's the reason for this?
  11. B

    4.3 from 90 gm truck good for boat?

    I 've come across a freshly rebuilt 4.3 from a 90 gm. It is also well priced. i've got a 96 in my boat with a cracked block. my old engine is the early vortec with balance shaft and 12 intake bolts. my timing cover used 6 bolts, but the block was drilled and tapped for ten. casting number 196...
  12. B

    pivot pin socket

    what size socket do i need for a merc alpha one gen 2? i'm pretty sure it's a hex socket, but as i'm at work i cant se it, and want to pick it up on the way home. thanks.
  13. B

    transom seal kit req'd

    was hoping somebody could give me some help. i've got a 96 lund with a merc. eng. and drive. i need to replace the bellows and gimbal bearing. I have found some on the internet, but unsure if they'll fit. my transom serial # is OF57???? the parts ad says it will fit alpha one/gen 2 from '91-99...
  14. B

    anybody have any experiences with rapid-o-marine?

    i see they have very well priced engines, and was wondering if there was a catch? they sound good, but has anybody dealt with them?
  15. B

    looking for 4.3 parts

    could anybody suggest good places to find parts for a 96 4.3lx? i'm specifically looking for a cam and lifters and a block, but need various others as well. used parts are fine, as well as used complete engines. thanks
  16. B

    4.3 marine swapped for a van 4.3

    hello, just bought a '96 lund tyee with a 4.3 engine. there is water in the oil(unknown reason, but knew about problem before i bought boat.) I haven't torn the engine apart yet, but am curious as to whether or not a 4.3 from a 95 astr van will fit? all i would use from the van is the block, as...
View older results
Top