Search results

  1. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    sealing the wood for the side panels/ rod lockers, and the console tops. three coats here, then i can install the vinyl and assemble, and then hook up the rest of the wiring. and install the controls.
  2. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    coolant hoses on
  3. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    manifolds on
  4. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    decided to clean up the manifolds a bit. didn’t take a pic in between, but i sandblasted them before painting. used VHT caliper paint. rated for 900f. should be well under that.
  5. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    was thinking of brushing on some aluminum coloured paint on the transom, but there is three coats of epoxy on it, so i don’t need the protection, just for looks. it is covered by an aluminum deck when done, so not exposed to uv. bilge area is painted grey, just dirty. might still pint the...
  6. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    wire harnesses ran to console. pretty happy with how it’s looking so far. just have to install exhaust manifolds and build the side panels and consoles now.
  7. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    engine is wired!! spent a bunch of time cleaning up all the loose wires. still need to mount battery switch.
  8. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    it’s coming slowly. always seem to get sidetracked with life. but getting there. hoping it will be ready for spring, so i can get it in the water as soon as the ice is gone!
  9. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    front deck
  10. B

    livewells- do they hang from underside of deck?

    this picture was taken as soon as i had the top off. it appears from this picture that there is about 1/2”-3/4” between top of livewell, and the underside of the top deck. the top deck sits on the aluminum bracket at the front, and on top of the side panel. the livewell is bolted to the top...
  11. B

    livewells- do they hang from underside of deck?

    not sure if this is the right place to put this, but figured there would be some knowledge here. i’m rebuilding my tyee, and currently installing my livewells. i assumed they sat on the floor and the deck basically sat on the top of the livewell. except i have too much height there. i could...
  12. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    also spent a couple hours tidying up a wiring harness. looks WAY nicer covered in loom. also makes it seem less confusing to install when it’s all organized.
  13. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    finally got back at it! installed the front compartment and started on the livewells and consoles.
  14. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    got the motor put back in place, nice to have the space in the shop it was taking up.
  15. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    livewell tops and doors. i didn’t take a picture before i took the old ones apart, but they were worse than the front now compartment above. still working on it, but it’s very slow!!
  16. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    new wood, epoxied, and new carpet glued on!! looks so much better. little bigger gap than i thought for the edges. this compartment door was quite tight before and feels the same with new carpet.
  17. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    started taking apart the front deck and compartments. old carpet was pretty worn! and some rotten wood too.
  18. B

    seat mount for springfield adjustable height base?

    Part #3100531-LAR1 is a slide Part #3100031-LAR1 is a swivel this is what they sent me. looks correct to me.
  19. B

    seat mount for springfield adjustable height base?

    i contacted springfield directly, they immediately sent me the part number of the base i need. this one is separate from the pedestal, although it appears my two taper-lock pedestals are integral with the bases. i haven’t look too far into those yet though. $40 ish bucks for a base is not too bad!!
  20. B

    '96 lund tyee 1850 floor rebuild and foam replacement.

    got the floor carpet all glued in and tucked in. took a bit of work as i kept the gap between floor and side pretty tight.
Top