Search results

  1. Thirsty Endgrain

    '84 Aquasport osprey 19.5' - Good boat?

    Locally there is one for sale, and it has my interest piqued. It's well cared for and clean, I just know nothing about them. I have looked around at some of the available info, and am seeking advice here too. I currently have a '64 glasspar seafair sedan, which I love! But I want a CC for...
  2. Thirsty Endgrain

    Boat shuts off after a few seconds.

    It sat for 14 years, and you tried to run it without first replacing the water pump impeller? There in fact is a possibility that damage was caused. No water coming through is a bigger issue than it shutting off. If it were me I would not try any more starts, pull the LU off and replace the...
  3. Thirsty Endgrain

    '84 Johnson 90HP died in water, won't restart

    Good to know, I'm still at a loss for what caused me to be stranded. Hopefully I'll find something amiss when I pull carbs off and inspect.
  4. Thirsty Endgrain

    '84 Johnson 90HP died in water, won't restart

    Wasn't pumping hard, but when I did switch the tanks and try restarting, it wouldn't start. Then I started priming, and then no start until battery died. It made me loose a lot of faith in this engine, because it was a 6' swell day and not a situation I wanted to not have my main engine alive...
  5. Thirsty Endgrain

    '84 Johnson 90HP died in water, won't restart

    Should've said: It took a lot of cranking to eventually kill the battery. Starter is new, it engages and cranks no problem. Cables are tight and in good condition. So I at least don't think it's a starter/battery issue. Something with carbs/fuel delivery etc.? Can these things become flooded...
  6. Thirsty Endgrain

    '84 Johnson 90HP died in water, won't restart

    Well I was out in the open ocean (nearshore), and after switching my fuel tanks to make sure I had plenty for the ride into the mouth it simply wouldn't restart. Ran all day just fine before that. Switched tanks, primed bulb until stiff, and just nothing. Ended up killing the battery trying to...
  7. Thirsty Endgrain

    Launching + boat ramps with 2WD Sprinter

    Almost done with the restoration I never intended on doing and about ready to get the darn thing wet. I will exercise good sense in determining if a boat launch is within the van's capabilities, try not to launch/retrieve at low tides or if the ramp is slimy etc. Thinking I'll throw a few...
  8. Thirsty Endgrain

    1964 Glasspar Seafair Sedan - minor restore w/questions.

    Haven't been posting about it but I've been busy. So I did gelcoat, and got the bottom paint on. Electrical is allllllmmmost done done. I can flip switches and various things turn on, the correct things even! Anti-skid paint on the deck, a bunch of the fiberglass painted a nicer color than sun...
  9. Thirsty Endgrain

    Greasing creaky tilt and trim

    I can't get grease into the top of the tilt ram pivot point. Pics attached. Is there something missing here, should there be plugs or a bolt through this hole? When I pump grease into the zerk shown, it immediately comes out of the holes on either side of the steering column, and the t&t creaks...
  10. Thirsty Endgrain

    "New" '84 Johnson 90HP V4 - questions

    Still wondering if anyone has insight into the head cover gasket questions above. Also, I have a new valve body for the thermostats, and one that came with a used cover I got off of eBay. The new valve body has one little hole at the bottom, and the older one has two little holes. I'm assuming...
  11. Thirsty Endgrain

    "New" '84 Johnson 90HP V4 - questions

    Ran it for about 3 mins the other day after finally getting it hooked to the boat with controls et al., and noticed that the port side head was almost too hot to touch. Starb side was nice and cool. So naturally did a little bit of investigating and found a bunch of corrosion in the heads'...
  12. Thirsty Endgrain

    1964 Glasspar Seafair Sedan - minor restore w/questions.

    OK got the keel glassed. I have gelcoat, wondering if it's necessary to put some gelcoat on first, or should I just get the bottom paint on? How important is gelcoat?
  13. Thirsty Endgrain

    '84 johnson 90hp - regulated rectifier needed?

    Strangely, I have T&T but I don't think I have a regulated rectifier. I think someone added the T&T at some point in the engine's life because it also didn't have the relay box in the normal spot mounted on the engine. Putting the pieces together here, like usual. I don't know what the water...
  14. Thirsty Endgrain

    Adding GPS to VHF

    Alright, I have a West Marine VHF 585 that came with the boat and I want to add GPS for DSC. I think I can either tail off of the old Lowrance Elite 5HDI for the signal, or get a little standalone GPS puck antenna. Trying to figure out the best option here. The questions: -what cable end is...
  15. Thirsty Endgrain

    '84 johnson 90hp - regulated rectifier needed?

    It's sure is always something. I still haven't gotten the boat wet yet, as I sally forth into the realms of all things fiberglass, wood, electrical, mechanical, etc. Anyway I just fired it up to check that the tach wiring was all Gravy, and noticed that as I increased rpm's the voltage would...
  16. Thirsty Endgrain

    84 johnson 90hp throttle cable not lining up

    This angle kinda shows it a bit better. I'm at a loss.
  17. Thirsty Endgrain

    84 johnson 90hp throttle cable not lining up

    J90MLCRD Finally got the thing mounted to the boat and seemingly no matter what I do the throttle cable seems cocked and it's hard to move from the remote. I tried to take pics to show it but it's really hard to show from any angle. The guide that's attached to the carb cover just doesn't seem...
  18. Thirsty Endgrain

    What should I do to this trailer?

    Please don't say junk it. It seems ill designed to me, but I also don't know much about boat trailers. I've been figuring out the boat part, but I wanna make sure that once I start lugging this thing around it's safe and supportive and I'm not putting anyone or thing in danger (more than...
  19. Thirsty Endgrain

    1964 Glasspar Seafair Sedan - minor restore w/questions.

    Still trying to figure out the keel. It seems like to do it right I need to do some glassing. Current plan until I'm advised, coerced, or otherwise bribed into some sense is to sand out a couple-few inches of the gelcoat away around the affected area, cut 3-4 long pieces of fiberglass stepping...
  20. Thirsty Endgrain

    Carb rebuild Q: 84 johnson 90hp

    I know I have another thread going, apologies if I should post in that but it's getting cluttered with my other questions. Just got the carb kits and I'm going through them (again-now actually having the kits). They came with o-rings at the drain screws, but the old ones leaked when I put it...
Top