Search results

  1. ct1762@gmail.com

    johnson 150 Low Rpm

    these 60 degree motors do not like a bad OMS pump diaphragm. they can do some strange things. ditto for the optical sensor/pack combo. Ive had a few that seemed to be fuel related, but was ignition.
  2. ct1762@gmail.com

    Gearcase compatibility - V4 Crossflow question

    Anyone know if its ok to use a 1991 and up lower on a 1989 v4 crossflow? Ive got a gt100 (1989) and a 1993 88spl with a good lower. The driveshafts are different, but I bolted up the 88 spl to the GT100 and it seemed to go toghether fine, but hope the newer gearcase isnt a tad bit longer as i...
  3. ct1762@gmail.com

    1991 Evinrude 60hp VRO - Won't Idle

    its going to be near impossible to set the idle speed/low speed jets correctly when its severely running too rich of an oil mix.
  4. ct1762@gmail.com

    1996 130HP Evinrude V4 looper water pressure gauge install question

    well yes. if the spring isn't stiff enough, it will unseat the grommet as I had mentioned something must've been leaking! if they leak, you are screwed as the water pump can't get enough pressure to tip it up and over down into the heads. also these new t stats are horrible. the old ones with...
  5. ct1762@gmail.com

    1996 130HP Evinrude

    you bet. but you'd see water right away in the filter (hopefully you have a water separating filter with this terrible corn gas?). other thing i've done very succesfully is get a $15 manual fluid extractor, stuff as long a hose in it that you need to reach the corner of the tank, and suck away...
  6. ct1762@gmail.com

    1996 130HP Evinrude

    you will need to hook a dva meter up with a primary terminal extender to see what voltage is doing when the motor acts up. if it dumps then the motor skips, you have an issue with the pack or stator. I'd just cranking voltage test the pack, timer base and charge coil to make sure its all in...
  7. ct1762@gmail.com

    1996 130HP Evinrude V4 looper water pressure gauge install question

    well something MUST be leaking at idle in the t stat housing. The plastic t stat seat could be it, or the grommet got rolled, or the metal ring is missing which (i think) compresses the spring to the proper tension. other thing to do would be to remove t stat housing and make sure water is...
  8. ct1762@gmail.com

    Warning buzzer

    pop off the t-stat housing and take a peak. as mentioned, if the poppet valve grommets are crusty and leak, it will overheat a low speeds. t stats should be replaced while your at it.
  9. ct1762@gmail.com

    Fuel pouring from hood?

    if you can do one carb, you can easily do all 3. just take plenty of pictures and count low speed needle turns so you put them back correctly (usually require a little adjustment after removal). only a couple linkages, fuel line to each carb, and the choke link to undo!
  10. ct1762@gmail.com

    Yamaha 2 stroke crank bearing, to grease or not to grease?

    well the motor will not last if you don't mix oil and fuel... not sure what you mean by giving it a try? heavy grease might block the passages for fuel/oil mix to reach the bearing long enough that it overheats. a drop or 2 of tcw3 is all that I use on bearings just before the crank case gets...
  11. ct1762@gmail.com

    Suzuki DT100 -90 Gauge monitor

    you mean the colored leads are missing , or just the connector? if its just the connector why cant you snip off the other ends and bullet-connect everything together? dont the lead colors match up?
  12. ct1762@gmail.com

    1996 130HP Evinrude

    when you say "bogs down until i back off" does that mean it clears itself out and is fine at full throttle? or stays bogged? if it clears itself out id say its most certainly a carb issue.
  13. ct1762@gmail.com

    1996 130HP Evinrude

    "looking closer" at sealing rings requires a complete powerhead teardown. might as well send the block out and get it bored for a complete rebuild at that point.
  14. ct1762@gmail.com

    100+ outboards

    MASSIVE difference between a 1986 (prop rated) OMC 2 cyl looper and the old 35 crossflows in my opinion, especially out of the hole. But I agree, balance matters for overally enjoyment on a small stern-heavy boat.
  15. ct1762@gmail.com

    1980 115 johnson stumbles at 2500rpm low compression cyl 3

    ha didn't think so. one guy claimed they can get up to 3-4 sizes larger.Never worried me.
  16. ct1762@gmail.com

    1980 115 johnson stumbles at 2500rpm low compression cyl 3

    well put thanks. also, the jets do wear themselves a bit over the years or so im told never actually compared to a new one.
  17. ct1762@gmail.com

    1991 Evinrude 60hp VRO - Won't Idle

    there is a reason the service manual (you do have a factory one right?) says in black and white "Always PUSH fuel lines off, never pull"
  18. ct1762@gmail.com

    1977 55 hp evinrude

    it won't idle or it idles too high? very different issues. if it wont idle then yes carbs need cleaned (should do it anyway). a high idle can indicate an air leak or the cam roller is against the throttle cam causing the throttle plates to be open a hair.
  19. ct1762@gmail.com

    1996 130HP Evinrude

    #1 is to make darn sure its not overheating and your overheat alarm works.
  20. ct1762@gmail.com

    '84 Johnson 90HP died in water, won't restart

    i would start cleaning all ignition grounds starting with the coils. it would help to know if you have spark when its not starting. if it doesnt and you get stranded, disconnect the black/yellow kill switch. yours has 2 power packs racer would know if the kill wire is at the terminal strip.
Top