Search results

  1. flyingscott

    Am I getting water of of fuel path Properly 150's J150VXCIS 2001 carbed 150'

    Get a cheap 12 volt pump and drain your tanks
  2. flyingscott

    1996 mariner 115 HP wont start

    Ok your controller should have a button in the middle of the throttle. Push that in to disengage the shifting function. This will give you a throttle only function for starting. Push the button in and push the throttle just until you feel resistance. Now while you are starting it, Push the key...
  3. flyingscott

    1996 mariner 115 HP wont start

    Are you using the fast start lever? What about the primer? Are you using that? Carbs back on the right cylinder? You know that's a 2+2 motor correct? Starts and idles on the top 2.
  4. flyingscott

    2002 Johnson 50 hp with a engine code 4-3 (fuel injector problem)

    Buy the factory manual and start testing
  5. flyingscott

    1995 25hp Johnson 2 stroke, what are the best years for the 25 hp?

    Have you priced the ignition parts? Only made for 5 yrs ,not going to have the parts availability of a 2 cylinder. Nothing wrong with the motor itself. Just too many model specific parts. The 2 cylinder is just as good and cheaper to maintain.
  6. flyingscott

    1986 Johnson 150 HP Crossflow V6 Rebuild - Now What?

    Mercury Yamaha and Evinrude all make good ones.
  7. flyingscott

    Adding charging system to 1997 evinrude 25 hp

    Which 25 hp do you have?
  8. flyingscott

    Mercury 75hp on aluminum 16’ Starcraft

    I have that boat. the weight is fine as the boat is rated for either a 85/90 hp motor. Those motors were around the 305 #s so I would look at your prop design. Is that the big foot or whatever they call it now.
  9. flyingscott

    1986 Johnson 150 HP Crossflow V6 Rebuild - Now What?

    run a decarb in your fuel. WSM is a factory style piston
  10. flyingscott

    I’m at a loss - Evinrude 40

    I will call BS on that kind of speed on that old of a 40 hp.
  11. flyingscott

    '23 Merc 15hp EFI alarm

    Aren't they under warranty?
  12. flyingscott

    1986 Johnson 150 HP Crossflow V6 Rebuild - Now What?

    If you put in factory pistons run a decarb in your gas. Use quality oil and make sure the thermostats are working.
  13. flyingscott

    1993 evenrude 70 hp compression

    When the head comes off you can see it. It will be on the piston either a part# and or size. May need to clean the pistons off to see it
  14. flyingscott

    1993 evenrude 70 hp compression

    Check the piston size before anything.
  15. flyingscott

    1993 evenrude 70 hp compression

    get a different compression tester and try again
  16. flyingscott

    1993 evenrude 70 hp compression

    that's pretty common for the middle cylinder to be damaged on those. There was a service bulletin for the peehole to be re located to the top of the block to prevent that. Is that Done? try a different gauge, or pull the head off
  17. flyingscott

    1995 25hp Johnson 2 stroke, what are the best years for the 25 hp?

    anything just not a 3 cylinder.
  18. flyingscott

    1989 25hp Evinrude compression release

    Does that have a recoil starter on it. Those motors are pretty stout to pull. Check all your electrical connections. Make sure they are shiny clean the grounds on the block also.
  19. flyingscott

    looking for advice on a 1996 merc 15 hp.

    buy a different motor. Converting it to a tiller is going to be expensive by itself. Then you have the lower unit problem which is a known issue on those motors.
  20. flyingscott

    1991 Mariner 115 4 Cylinder 2+2 Compression

    How does it run?
Top