Search results

  1. D

    Mercruiser Engine Mounts

    1. should be, guessing that's weight per mount = 700lbs 2. most mounts are held down with 1/2" stainless lag bolts and sealant/adhesive 3. possibly, some of the non balance shaft 4.3 used a fluid filled mount, easy to ID by the cable straps fore and aft of the fluid bushing on the mount. Do...
  2. D

    mercruiser 7.4 (L29) firing order

    okay, but did you actually verify good consistent spark? would be next to impossible to install the rotor 180 off have you inspected under the distributor cap? usually when replacing the plugs its a good idea to r and r the cap/rotor as well
  3. D

    1981 MerCruiser Outdrive Water Pump

    i would go with the latter of the two links you posted, the amazon one appears to be sierra. never had any luck with the sierra pumps, you're better off with oem fyi the second pump assy does NOT include the base assy which you definitely should be replacing as well
  4. D

    mercruiser 7.4 (L29) firing order

    have you checked for good consistent spark at the coil lead?
  5. D

    Boat is in the shop. Sad day.

    being an efi volvo and based on your description/diagnose over the phone i'd say your mechanic is on the right track. and yeah, price sounds relative to parts and labor (not sure of the shop rate). those pumps are spendy, especially the dual pump assys. testing the fuel pump pressure(s) will be...
  6. D

    4.3 blows 15a fuse when you throttle up

    you mentioned in your op, that a 15 amp fuse was in place of the breaker? a fuse will blow if there is a short to ground or the current in the circuit exceeds the rating of the fuse, my guess is the latter in your case. could be due to corrosion, loose connection, etc... i can't recall ever...
  7. D

    No water out of outdrive

    1. top, bottom hose goes to t-stat housing 2. no 3. yes, but probably not part of your issue 4. yes, but probably not part of your issue most likely what is happening is the sea water pump impeller has a set and is having a difficult time priming on the muffs (common for brass housing pumps if...
  8. D

    Ignition switch failing?

    the ignition fuse is most likely at the fuse panel not in-line, i think an in-line fuse was merely suggested for you B = battery constant 12 volts I = ignition, 12 volts in the "run" position S = start, 12 volts in the "start" position easy to test with a voltmeter
  9. D

    4.3 blows 15a fuse when you throttle up

    the breaker in an oem harness at the red/pur wire is 50 amp curious as to why the engine harness was replaced?
  10. D

    Power Steering high pressure hose coating flaking off

    agree with dingbat, hose is beyond useful (safe) life local high pressure hose/fitting shop can make a new one for you, cheaper than going oem, if it's even still available
  11. D

    I screwed up! Did I damage anything?

    probably didnt damage anything, the gimbal bearing does rotate quite a bit and seeing as how the alignment is good now there's little chance of any damage
  12. D

    87 bayliner ciera 2450 will not shift out of forward, any suggestions??

    guessing this is an older style aq/dp drive? could be simple as a cable adjustment possible other causes would be remote control issue, shift linkage at drive, shift foot binding in clutch/clutch issue...
  13. D

    Impeller housing

    it may, and probably will at some point another issue is that it may draw air and cause the pump to not work properly resulting in an overheat the replacement pump is solid brass unlike the original (as shown) which has plastic barbs pressed into the brass housing
  14. D

    Alpha One Gen II problems

    tilted up the sound you are hearing is the u joints, don't ever run the engine with the drive trimmed up past the trim limit, you will seriously damage the u joints and other items have you tried adjusting the cable(s)?
  15. D

    No spark while cranking

    might be the module but most suspect for no spark on a thunderbolt is the ignition sensor in the distributor
  16. D

    engine stalls when shifting back on forth a lot

    could be the lower cable hanging up and causing the shift interrupt switch to stay engaged too long may be time to replace the lower cable
  17. D

    Drive won't engage in forward gear. Reverse works fine

    verify cable adjustment is correct, if still no go may have to replace lower cable or there is an issue with the shift linkages
  18. D

    Lower Unit?

    you didn't post any rpm readings
  19. D

    Turning engine off noise

    dieseling, not healthy for any gasoline engine likely causes are running rich, improper timing, idle speed too high, carb settings/needing rebuild, etc... best to start with a full tune up including fuel filter(s)
  20. D

    Rebuilt Mercruiser 140/3.0 doesn’t have enough power to plane

    a lot of info here... first off, get a new distributor cap points are set by using a dwell meter, feeler gauge is okay for initial set up but a dwell meter is used for final adjustment idle timing isnt a range of 6-10, depending on the vintage it should be either 6 or 8 btdc. engine info tag...
Top