Search results

  1. Scott Danforth

    Correct prop size

    What does your issue have to do with the OP's thread? the 6 questions in the sticky at the top of the forum take the trial and error out of the prop selection. Additionaly with a single gear, you can never get the best holeshot and the best top end with a single prop.
  2. Scott Danforth

    Yamaha 3.0 l4 engine fuel pump

    Go to summit racing Look up Carter Marine fuel pumps. Buy the one for the 3.0
  3. Scott Danforth

    5.7 MPI Misfires Under Load

    Compression gauge is off as new motor spec is 150psi fuel pressure is a bit low What is pressure under loat at WOT? backfire under load is usually running lean
  4. Scott Danforth

    Lost bill of sale

    If you have a signed title, you should be good to go
  5. Scott Danforth

    Old Sangstercraft.

    It's a generic plastic Bimini top fitting Available nearly everywhere You order by tube size
  6. Scott Danforth

    1994 OMC Sunbird Cuddy 190

    Remove the drive and motor Remove the interior Pull the rub rail Pull run rail screws Pull cap Wear appropriate PPE Fire up the saws
  7. Scott Danforth

    I/O taking on water while sitting not moving

    Looks like a rubber cap covering a Tee fitting that is now broken
  8. Scott Danforth

    Possibly getting a slip - what to know before saying yes

    Just my observation Even boats in Wisconsin get bottom paint when slipped Never fill your bilge to test anything Self bailing decks help to shed water above the deck. However most leaks happen below the deck. A second bilge pump and a high water alarm with wi-fi notification would be my...
  9. Scott Danforth

    1986 AQ131A Carburetor Options

    still quivering because its a solex carb on the motor...... here is one from NLA parts https://www.nlamarine.com/products/volvo-penta-855637-856046-841532-carburetor-carb-solex-aq131a-aq131b-fuel-pipe?variant=39885262159969 there are some smaller ones on evilbay. If you can find one from an...
  10. Scott Danforth

    1989 Mercury 2.4 Black Max 200 Service Manual

    http://publications.brunswick.com/ or your local mercury dealer for new ebay for used
  11. Scott Danforth

    My boat is being a boat . . .

    I would send a file to the laser and bribe the brake press operator with a 12 pack...... LOL
  12. Scott Danforth

    Trim/tilt issue 1996 Volvo Penta DP

    are you hitting the up trim limit so you have to then use the trailer button? are you following the troubleshooting guide in the factory manual? the main wiring for the motor goes to a circuit breaker or fuse mounted on the starter B terminal.
  13. Scott Danforth

    2018 V6 200 J Oil pressure dropping and alarm

    that is not what I stated. I simply re-iterated that your motor should have had many more oil changes as the oil is supposed to be changed at the end of each season prior to winter layup by both the service manual and the information that you received from the dealer However I would start with...
  14. Scott Danforth

    1994 OMC Sunbird Cuddy 190

    my guess, the floor would be 1/2" with 2 layers of glass on each side.
  15. Scott Danforth

    pontoon boat renovation

    You will have to get quotes from a shop. However know that these projects are usually done as diy
  16. Scott Danforth

    pontoon boat renovation

    Most shops charge about $120 per hour You are looking at about 60 hours or more because to replace the carpet, everything comes off.
  17. Scott Danforth

    What to do with my two 470's?

    That looks bad. You have to do a proper cam/lifter break in and hope you don't toast the cam lobe
  18. Scott Danforth

    My boat is being a boat . . .

    I would go 15 long. You will need to form it like the sport tabs for support, however a single ram will work Agree with AD, the sensors sit in the cylinders
  19. Scott Danforth

    Im fed up with this Boating life.

    The 3.0 uses a single manifold for intake and exhaust. Your manifold is busted and leaking water into your motor. Buy a new manifold and elbow
  20. Scott Danforth

    Upholstery Work?

    I did the upholstery assembly and hired out the sewing Just as a comparison a new 24 foot center console has about $6-8k worth of upholstery in it. Helm seats, coaming bolsters, coffin box and folding aft seats
Top