Search results

  1. Scott Danforth

    Alpha gen 2 housing to gen 1 outdrive

    You can do the swap in 3 easy steps Step 1: sell the drive you have for small pile of cash Step 2: empty wallet onto pile to make pile bigger Step 3: take bigger pile of cash and buy the drive you need
  2. Scott Danforth

    1988 Rogue 2420

    I told her (jokingly) that she is banned from any power equipment The Briggs Intek is apparently known for pushrods bending based on the amount of hits I got on my search About $100 in parts (gaskets, seals, pushrods, oil filter and spark plugs) most of which will be here tomorrow Just glad...
  3. Scott Danforth

    1988 Rogue 2420

    So, today was able to get the new carb put back together
  4. Scott Danforth

    1988 Rogue 2420

    Then she decided to cut the hedges and injured herself
  5. Scott Danforth

    1988 Rogue 2420

    So the Admiral was cutting grass a d the lawnmower motor ate a pushrod
  6. Scott Danforth

    Trim issues

    If it's an AQ series, the gauge is the limit
  7. Scott Danforth

    Trim issues

    fix your gauge you tube sucks get a proper manual. https://www.volvopenta.com/en-us/service-and-support/your-engine/manuals-and-handbooks/ for your 1994, are you running an AQ drive, or an early SX drive?
  8. Scott Danforth

    Small piece of plastic drain plug went into exhaust manifold

    here is what will most likely happen the small part may get wedged in the manifold or riser, upon shut-down, the part may melt a bit, making itself smaller. then it will get washed further out the system until its stuck in the discharge of the elbow. upon shut down it will most likely melt...
  9. Scott Danforth

    Merc 4.3 v6 distributor cap and cilinder connections

    possibly. however do not count on it. find TDC on the motor, look at the rotor location. that is tower 1
  10. Scott Danforth

    Updating the 39 year old Tyee

    I would install the bases myself you could always bolt in a block-off-plate
  11. Scott Danforth

    Merc 4.3 v6 distributor cap and cilinder connections

    Never assume the tower on the dizzy is in a specific location. The tower the rotor is pointing to when the motor is at TDC is number 1
  12. Scott Danforth

    Merc 4.3 v6 distributor cap and cilinder connections

    Why not just use the proper GM or Mercruiser diagram
  13. Scott Danforth

    Merc 4.3 v6 distributor cap and cilinder connections

    Follow your sketch. You have tower 1 of the dizzy going to cyl 3
  14. Scott Danforth

    Merc 4.3 v6 distributor cap and cilinder connections

    Your sketch is wrong Cylinder 1 is port forward
  15. Scott Danforth

    1988 Rogue 2420

    So the HP830 carb I picked up appears to be unmolested other than mud dauber larva in the vent tubes. Guy I bought it from had it on a 502 in a boat and couldn't get it to idle right. 3 if the 4 idle screws were only 1/4 turn out. One was out 1.5
  16. Scott Danforth

    Exhaust Bellow

    That is always where you start
  17. Scott Danforth

    Updating the 39 year old Tyee

    I would not put a ski tower on it. Look at the turbo swing
  18. Scott Danforth

    Mercruiser qsd 2,8 Tuning box connections

    You plug into the CAN connector
  19. Scott Danforth

    87 PCM Chevy inboard temp / water pump issue

    Your exhaust manifolds may be plugged
  20. Scott Danforth

    Merc 350 mag mpi HELP! 200°

    go back to the person you paid and ask if they found all the impeller bits if not, start pulling things apart yourself overheat is a direct result of lack of cooling water flow.
Top