Search results

  1. Scott Danforth

    Volvo Penta 5.0 GL-B does not go properly

    do not stick anything metal in the passages other than maybe a piece of soft copper wire. the bowl, metering plate and throttle body are made of zinc and easily damaged. do not use simple green cleaner or bleach for the same reason.
  2. Scott Danforth

    Boat won't go over 3000 RPM no mater what prop I use

    @achris if the ECM doesnt know its in gear, i believe the ECU limits the RPM to 3000. Am i correct? I believe this is why you stated look at the in-gear switch
  3. Scott Danforth

    Waterproof seal on Nautolex clad surfaces

    butyl tape will make a seal, even if it doesnt stick to the nautolex. the top layer of the nautolex is designed so not much sticks to it.
  4. Scott Danforth

    Sx outdrive water pump

    thermostat should be 140F your elbow temp with an IR gun should be about 150-170 if you have that much rust in the t-stat housing, you need to pull the manifolds and elbows to inspect.
  5. Scott Danforth

    2006 Volvo 5.7 osi-d crank no start

    your motor has a 55psi oil pump pressure relief. if you run a good 20W50 oil and the motor was cold, your oil pressure will be a bit higher. 60 psi is not a problem
  6. Scott Danforth

    Engine swap, OMC to mercruiser

    the stringer drives were the OMC drives available from the 60's to 1985. they used a machined splined "button" about the size of a large hockey puck that bolted to the crank. the intermediate housing was the gear box assembly that bolted directly to the flywheel housing flange on the engine...
  7. Scott Danforth

    Volvo Penta 5.0 GL-B does not go properly

    go thru your carb and rebuild it. by your description in post #1, it sat for a while. the fuel that was in there, has now turned to sludge from sitting and gummed up the circuits. its a holley 500 CFM 2300 2-barrel. to do a proper rebuild should take someone experienced about an hour total...
  8. Scott Danforth

    Alpha One Gen II, unknown part

    do a parts search for the proper flappers per your serial number
  9. Scott Danforth

    Outdrive oil leak

    Wix makes some of the best filters. FRAM is some of the worst. the NAPA brand filters are WIX you can also run 15W40 rotella in the motor. however 5W30 is way too light a viscosity
  10. Scott Danforth

    How would you do this transom?

    you need much much much more than a transom. you need a full restoration. especially since your floor is rotten which is always the last thing to go.
  11. Scott Danforth

    Unknown 55hp Johnson boat restoration

    you have a full hull restoration ahead of you. suggest reading the stickies at the top of the forum. specifically this one https://forums.iboats.com/threads/how-tos-and-other-great-information.283508/ and read links 14, 15, 18, 2, 3, 4a, and 4b in that order. if your floor is shot, your...
  12. Scott Danforth

    Sx outdrive water pump

    the thermostat is held in place by a sleeve. with the amount of rust you have there, you may want to look for a new one. I would get some oxalic acid (available on amazon) and soak the thermostat housing in it for about a week to dissolve the rust. I would also suggest you pull your exhaust...
  13. Scott Danforth

    Crest Mooring Cover

    Possibly. However to be guaranteed, most will want to measure themselves Best is contact your local marine canvas upholstery shop
  14. Scott Danforth

    Pontoon boat Engine too low?

    Pontoons need a hydraulic jack plate in addition to T-n-T.
  15. Scott Danforth

    How would you do this transom?

    Pull the cap Cut out the deck, replace the transom, stringers and deck Your transom is shot, your stringers are also rotting, and your flotation foam is probably water logged
  16. Scott Danforth

    Mercruiser 5.0 Oil Pan Replacement Tips

    Pull the wheels and run the hubs on a 2x4. Gain you a foot
  17. Scott Danforth

    Engine swap, OMC to mercruiser

    Stringer coupler buttons only available for 2-piece RMS cranks Cobra coupler only available for 1-piece RMS crank
  18. Scott Danforth

    Outboard cowl paint help

    Gloss black
  19. Scott Danforth

    Outboard cowl paint help

    get a primer and paint with a hardener. rattle can paint is just solvent dry paint and not a catalyzed paint. merc phantom black is just PPG Black. same as GM Tuxedo black and Rustoleum black. I would get a quart of rustoleum, a bit of urethane hardener (from tractor supply and spray it with...
  20. Scott Danforth

    Fix it videos

    in addition to the erroneous information. I find it odd that they talk for 10 minutes about nothing before getting to the repair/mod/etc. by then, I have downloaded the manual, read it, understood it and work on the repair.
View older results
Top