Search results

  1. Scott Danforth

    What Lube to Pull (or Push) Fuel Fill Line through ABS Pipe?

    you are going to have to push and pull that fuel hose thru any bend
  2. Scott Danforth

    Tracing the trim problem

    you need the EVC manual (Electronic Vessel Control)
  3. Scott Danforth

    Trust the dealer?

    welcome aboard. how loaded will you be? just yourself? yourself and 3 buddies? as indicated above, it is assumed the average adult is 150#. some of us famine proof boaters are over 200#, some close to 3X what the average adult weights. so how much are you adding in terms of weight? gear...
  4. Scott Danforth

    Canoes Is there a department dedicated to canoes?

    Sears had multiple companies private brand stuff for them for years. As Bondo mentioned, doesnt matter. Its an old fiberglass canoe. Repair is no different than a fiberglass boat
  5. Scott Danforth

    What Lube to Pull (or Push) Fuel Fill Line through ABS Pipe?

    KY jelly will work
  6. Scott Danforth

    Pontoons - Growth from being slipped...what is it?

    Which is why the prior owner paid someone to clean it with muratic acid and a pressure washer
  7. Scott Danforth

    7.5 Mercury Issues

    You need the venturi tube You also have dirt in the carb
  8. Scott Danforth

    Bravo 3 with small leak from prop shaft

    I would reseal the drive
  9. Scott Danforth

    Pontoons - Growth from being slipped...what is it?

    High mineral content. its basically hard water deposits.
  10. Scott Danforth

    Re-upholstery Job on Cruisers Yacht 338 Bowrider

    and to let the seat breath when water gets on it and soaks thru the stitching
  11. Scott Danforth

    Bought a new long block and wondering about the coupling and gimbal bearing.

    use the grey RTV for waterpumps
  12. Scott Danforth

    Gelcoating keel

    if you have a fiberglass supply house near you. start there.
  13. Scott Danforth

    Re-upholstery Job on Cruisers Yacht 338 Bowrider

    If it doesnt work out, repattern until it does
  14. Scott Danforth

    6.2 vortec head torque setting?

    If you over-torqued them, did you damage the block threads or the bolts? Bolt torque is listed as 65 ft-lb for an SBC. The extra 10 lb-ft should not be an issue, however not guaranteed.
  15. Scott Danforth

    Gelcoating keel

    You will need to scuff the area, then roll on the gel. I would suggest a keel guard if you intend to beach
  16. Scott Danforth

    Mercruiser 3.0 = Chevy 181 CID = Small Block Chevy Valve Train? 1:65 Rockers?

    I would beg to differ. Remove a thermostat and see how badly a system cools. Thermal transfer requires a specific time for water to pick up heat. That time is controlled by velocity.
  17. Scott Danforth

    Tracing the trim problem

    There should be 5 manuals. One for base engine, one for the drive, one for the EVC which is what you need for the trim system reset, etc, one for the fuel system (efi) and one for controls I believe the drive manual is 7746477
  18. Scott Danforth

    6.2 vortec head torque setting?

    The torque setting depend solely on which fasteners you bought
  19. Scott Danforth

    Restoring my boat

    Either christmas tree fasteners or z-clips
  20. Scott Danforth

    opinions: best way to replace swivel shaft and gimbal ring on bravo

    Pull the motor
Top