Search results

  1. Scott Danforth

    Boating YouTube channels

    only one that I would suggest is Frisco Boater as he got his info from here. most you-face-tube-book posts are incorrect.
  2. Scott Danforth

    Frozen Prop on SX-M Duoprop, Seeking Advice

    now buy a few tubes of prop shaft grease.... https://www.iboats.com/shop/volvo-penta-grease-3809449.html
  3. Scott Danforth

    Hydraulic line

    stainless hoses are rated at 3000 PSI most tilt/trim systems run in the 2500-2900 psi range on raise which is why most tilt and trim systems have stainless hoses
  4. Scott Danforth

    Windows 11 yes/no?

    its one digit higher than 10.... just like iPhones
  5. Scott Danforth

    Re-upholstery Job on Cruisers Yacht 338 Bowrider

    the issue is the older fabrics, threads, and foams were allowed to use arsenic as the anti-microbial. that went away in 2004. so the new fabrics and threads will not stand up to the fabric and threads from 20 years ago.
  6. Scott Danforth

    Re-upholstery Job on Cruisers Yacht 338 Bowrider

    Ted, If you plan on keeping the boat for a long long long time. I would look into Sunbrella Horizon line of vinyl and look at the PTFE threads such as Solarfix. the thread in clear/white/black is $142 a pound. the vinyl is about $18/yard there are many of the texile patterns and colors...
  7. Scott Danforth

    Hydraulic line

    take the old hose to a hydraulic shop and have a new one made
  8. Scott Danforth

    Intake choice

    336781.....73-85...oval...OPEN...454, 118cc chamber, 256/114cc ports its a BBC not an SBC like I thought. Perimeter bolts are all that was available on BBC these are some of the better open chamber heads from back then. 2.06/1.72 valves. I would do a bowl blend and casting flash removal on...
  9. Scott Danforth

    adding electric start

    Cost of conversion is always more than selling what you have and buying what you want
  10. Scott Danforth

    Intake choice

    Perimeter bolt is 85 and older What is full casting number? Do you have the correct intake that matches the heads?
  11. Scott Danforth

    Intake choice

    Are heads stock 1990? Or other? Yes on the marine manifold.
  12. Scott Danforth

    Frozen Prop on SX-M Duoprop, Seeking Advice

    Prop and hub are bonded with rubber. Maybe heat the prop enough to break the bond and pull prop off hub Then put puller on hub
  13. Scott Danforth

    Volvo Penta EVC tachometer LCD

    Volvo buys the tach complete from an outside vendor. either VeeThree or Faria
  14. Scott Danforth

    Frozen Prop on SX-M Duoprop, Seeking Advice

    volvo recommends pulling the props and greasing the shaft often to prevent this vary issue. with only owning it for 4 months, it sounds like you may not have pulled the props when you got it. I have had to cut props off because the hub was stuck to the shaft from lack of greasing. once the...
  15. Scott Danforth

    Windows 11 yes/no?

    did they get rid of all the bloatware?
  16. Scott Danforth

    Windows 11 yes/no?

    Im still running Windows 7 at home
  17. Scott Danforth

    Duo prop seal replacement

    yes
  18. Scott Danforth

    Timing pulley hits the chain cover

    Front crank sensor reluctor ring
  19. Scott Danforth

    Duo prop seal replacement

    Yes, to replace the input seal, you should have a new crush sleeve to set bearing pre-load correctly
  20. Scott Danforth

    Compression ratio 5.7l

    stock GM Vortec heads (both the 062 and 906) are listed as 64, measure about 65. not sure what the Summit head is.
Top