Search results

  1. Scott Danforth

    HIN & MIC

    GBP GIBSON BOATS 130 DAVIS STREET PORTLAND TN
  2. Scott Danforth

    Volvo Penta 4.3GL-C bogs and surges when hot

    well, the crud that was in your tank is now in your anti siphon, fuel pump and carb. that 1/4 tank of varnish sludge got broken up into floating bits of crud by you adding isopropyl alcohol. then you added good fuel to that to have a tank full of floating crud fuel. check the strainer in the...
  3. Scott Danforth

    Dump gun set up gelcoat

    yes think of trying to spray pudding. that is what gel is. to get it to spray, you have to thin it to at least the consistency of store bought gravy
  4. Scott Danforth

    Red Tide

    youre right, for some reason I called it Whiskey D's...... LOL could be confusing it with Joey D's chicago pan pizza
  5. Scott Danforth

    Dump gun set up gelcoat

    cant get much larger than a 26 foot boat dump guns are finicky and you have to have experience with them to get them dialed in. temperature and humidity are two things that effect settings. you most likely will need the duratec additive. and yes, while gel is expensive at $20 a quart, its...
  6. Scott Danforth

    Boat Manual

    those are the mercruiser manual numbers you can buy new from here https://publications.brunswick.com/ or you can buy used on fleabay and if you did not get rid of adobe flash, you can still view them in here. https://boatinfo.no/lib/library.html
  7. Scott Danforth

    Engine rotation

    If you have an I/O, you have standard rotation
  8. Scott Danforth

    Dump gun set up gelcoat

    to get consistent spray, I needed to add the Duragloss 904 additive I used this gun. https://www.amazon.com/Vaper-HVLP-Spray-Gun-Plastic/dp/B000BTJALA/ (same gun my local fiberglass retailer has for double the cost) set at 45 psi at the gun you still need to sand and polish, however it came...
  9. Scott Danforth

    Engine rotation

    unless you have a really old boat with inboards, you have a left hand rotation motor (standard rotation)
  10. Scott Danforth

    Trying to install a gen 4 502 mercruiser, need help!

    if you did not get rid of adobe flash, you can still view them in the library on https://boatinfo.no/ otherwise you buy them from https://publications.brunswick.com/ you can also put your serial number in BAM to see exploaded views of the parts manual. https://www.mercruiserparts.com/ it...
  11. Scott Danforth

    U-joint seized into gimbal bearing

    this corrosion needs to be fixed before the boat can go back into service two choices, new housing or take the current housing to someone to grind out the bad corrosion and weld in new metal.
  12. Scott Danforth

    Size of bolts on raw water supply pump??

    you mean the little M4 or M5 screws? take to your local ACE and find.
  13. Scott Danforth

    Mid 70 18ft ss I/O rebuild

    then that is the wrong man-over-board switch. I/O switches open when you pull the lanyard. they are wired in the pink wire from the ignition key to the engine outboard Man-over-board switches close in the off position. they are wired between the ignition and ground to ground out the magneto...
  14. Scott Danforth

    Gmorning from Argentina.

    welcome aboard the factory service manual is the best place. https://outboardbooks.com/
  15. Scott Danforth

    120 Mercruiser 2.5L - No spark

    exactly what it states and what AD re-iterates because you have a dog clutch and not a cone clutch, without the shift interrupt you can not get the engine into neutral unless you key off and shift, then key back on to catch the motor. it not that its hard to shift, it is that it wont shift...
  16. Scott Danforth

    Bad mixture? Help

    or running lean from crud in the fuel system or lugging load from too much pitch on the prop.
  17. Scott Danforth

    No trailer switch?

    that is a tilt and trim switch. I bet either you push it further up (second detent), or you push down and up
  18. Scott Danforth

    120 Mercruiser 2.5L - No spark

    you will have to key off to shift from in gear to neutral if you disconnect the shift interupt
  19. Scott Danforth

    Trying to install a gen 4 502 mercruiser, need help!

    have you looked in the factory service manual?
  20. Scott Danforth

    2011 Mercury 4.3 inboard

    start by removing the stuff in the bilge that is in your way. basically anything to port or starboard of the engine that is removable. put a pillow or blanket in there, may have to lay across the engine and work upside down then if you need to remove engine bits to get to the spark plugs...
Top