Search results

  1. J

    Oil pressure gauge

    Oil pressure was between 40 and 50..I turned around and looked again...it was at 0...running on muffs. Ford 302. Gauge has full volts when key on...oil sender has 9.3..Any suggestions
  2. J

    Ford 302 alternator proper amp size

    I believe my alt has died...or is very close...it's old and I want to replace it .not sure what to buy as in amperage...I have a petronix igniter 2 distributor and only run a fishfinder for the most part...I took it out today and it ran rough. I don't believe it's putting out enough juice. Not...
  3. J

    Ford 302 50 amp wiring

    One wire to battery and one to wiring harness?...I ask because I have a pic of what looks like one to starter solinoid
  4. J

    Ford 302 thermostat housing

    Alright...so I cannot find the proper stat housing anywere. I am going to have one made and wondering about the bypass outlet. If I have it put on to the new housing do I just run a hose of a port in the water pump
  5. J

    Rochester 2gv carb gasket.

    I am unable it seems to find the right gasket...the one I was given is 60244....r5...I tightened carb down and I have a major vaccume leak at the base
  6. J

    Outdrive id

    4227404 is the number I found..mc-1 ?
  7. J

    Mc-1

    Curious about the square holes there...is there a purpose
  8. J

    1993 larson 4.3 coil

    A friend has asked me to find out what ignition coil he needs ohm wise. From what says it's canister style...any suggestions
  9. J

    Ford 302 rad cap temp gauge

    I put a cap gauge on hx...here's a pic of temp from about a 15 min run..fluid goes into barf can and then back as it cools. Does this temp seem alright..it hasn't went any hotter
  10. J

    Raw water flow

    Curious on how much water I shoukd see coming out of my exhaust and prop while running on muffler. Ford 302...mc-1. I just changed the impeller and housing. Could someone post a vidio if possible
  11. J

    Mercruiser start issue

    I have an issue with start...all of a sudden it wouldn't start and when I turn key to start the oil pressure and temp gage pin full...no dashlights...everything else works
  12. J

    Electrical issues

    I have developed an issue that has fried 2 starter soliniods...first time it was no start and the gouges jumped to full on...and same again...what could cause this
  13. J

    Heat exchanger leak

    I have developed a leak at the neck of me hx. It doesn't matter what cap. I have called out to have it replaced with a new one. Now would this issue cause air to get into the system as I think it would.
  14. J

    Ford 302

    I'm thinking of changing intake and carb to 4 barrel...pros and.cons...aside from fuel mileage.
  15. J

    Ford 302 spark plugs

    The plugs that came with the boat are autolite 123. Is this the appropriate plug or shoukd I change them. Carborated...petronix ignition...
  16. J

    2001 t9.9 4 stroke

    Engine runs all day long....once it's warmed up. Problem I am having is to get it warmed up I need to cover up and let go of the breather pipe to carb. Filter is new...oil..spark plugs...primer bulb isn't soft it seems to stay full...filter full of gas
  17. J

    Ford 302...21 foot fiberglass with cuddy

    I have recently installed a new engine and took it out...wot is about 3500 rpm and slow out of the hole to get on plane...my prop is a 14x19p 3 blade aluminum...it was suggested I drop pitch...16 was the suggested. Any thoughts or is that right
  18. J

    Starter solinoid

    Everything installed on new build. Went to do the initial break in on ford 302 and my starter is now grinding and won't kick out. It gets stuck. The engine fired right away but because of the racket I stopped. Perhaps shim it out? When the engine was still hanging I spun it by hand with starter...
  19. J

    Ford 302 petronix igniter 2 distributor

    Good day. I have finally received my dizzy. The engine from the machine shop is on tdc. I have backed it so the pointer is at 10 bdtc. My question is were should the rotor be pointing when distributer is in all the way. It is down all the way and it is aiming towards the left side of carb...
  20. J

    Water coming into bilge

    I replaced the bellows and also redid the y pipe. I put boat in water and there is a steady stream coming from just above the top y pipe bolt. Any suggestions
Top