Search results

  1. A

    Weathered Werner fiberglass ladder delaminating

    I have a Werner 20' ladder, stored in my barn, hangs on the wall for 26 years still looks like new !
  2. A

    Fuel came out overflow

    On my boat, I ran the 18 gallon tank empty and came back on a portable tank. Then added about 3 gallons of fuel at a time and marked the fuel gage after each 3 gallons added. Now, I know pretty close how much fuel I had left. After confirming the fuel gage reading a few times, I know how much...
  3. A

    Any experience with trying to sell a boat on Boat trader ? Effective ?

    Are you prepared to allow a survey or an interested buyer to do transom and stringer tests to test for potential wood rot ? Anyone with boat knowledge would want these test due to boats age, no matter how good it looks...just to big a risk. Extremely few glass boats of that age that have no...
  4. A

    Valve Lubricant

    I used Lucas Fuel treatment in my 3.0, not as a valve lube, even though it is, but as a fuel conditioner to keep out water and clean combustion chamber.
  5. A

    How to flip a 18 ft. aluminum boat

    First thought is two engine hoists, one front and one rear....lift and spin with the help of a couple friends
  6. A

    Any experience with trying to sell a boat on Boat trader ? Effective ?

    In my area, Craigslist was the hot spot many years back. We have a small town local newspaper that has worked well and the FB ads which my granddaughter does for me. FB is getting bad for no shows or scammers in the past couple years. Of course we all know Craigslist is mostly scammers. I...
  7. A

    Any experience with trying to sell a boat on Boat trader ? Effective ?

    I have used many advertising platforms to sell my boats, except the one you mention. Never had a problem selling my stuff. Some times I get numerous calls but they don't show up. Typically I have sold to the first or second person to show up. Now, I have to say this....my boats did not...
  8. A

    best muffs to use on mercruisers?

    If my old ones ever fail, the dual units look like they would work great. I don't have high hp big block engines that use volumes of water, so will hang on to mine for now. Many that my neighbors had troubles with were the square units, heard more than a few complaints on those.
  9. A

    best muffs to use on mercruisers?

    My muffs are over 40 years old and have always worked very well. Neighbors have bought several newer muffs and have had issues with them. My guess is the newer models are not made as well as they often ask to borrow mine. Yes, the excess water will spray out from around the muffs as mentioned...
  10. A

    Fuel came out overflow

    There upis also a device that installs in the vent hose, that makes a whistle sound when filling. When the fuel pressure from filling reaches the vent hose the whistle stops. This is where you shutoff the pump to let the fuel settle and create an air pocket so no fuel comes out. Another thing...
  11. A

    Random

    Kinda like the driver that did not see the hugh train in front of him ! We live in an active RR area. A few times a week, people run unto these giant locomotives, claiming they didn't see them.......
  12. A

    Bearing buddy issues

    Hmmm...there was on mine....never used EZ lube hubs that I can remember. My instructions from years back always recommended jacking up the wheel and spinning it both back and forth to help remove air pockets and distribute the grease. Been following those guide lines for over 40 years.
  13. A

    Bearing buddy issues

    The instructions on my BB state that the wheel should be jacked up so free to spin. Hubs should be spun in both directions while pumping in grease. Whenever I add grease, I always spin the wheels both ways.
  14. A

    1987 Crest III

    You might also replace the gasket under that black valve unit where the hose plugs in. Those often dry and can leak fuel there as well. Our local Marine parts store usually carry the gaskets and O rings for tank repairs.
  15. A

    Bearing buddy issues

    There is no seal on the outside, and I don't know when the BB popped off. It was dark at night, we went out for fireworks, so not sure when I lost it. About a 40 mile roundtrip to and from the ramp, at 65 mph, there was no way the grease was going to stay in there. The axle got hot enough the...
  16. A

    Random

    Had a similar thing happen around her some years back. Drunk driver running at high speed at night into a no wake zone and crashed into multiple docks and other boats. Unfortunately two were killed and numerous injuries.
  17. A

    Random

    His motor always seem to run ok, but I would never but one from him ! He claimed it was quicker than getting out a hose and would help lube the impellor.....
  18. A

    1987 Crest III

    Sometimes the mfgr info is in small print molded into the plastic tank, that can be hard to see. If your tanks are metal, that info us usually painted on it or on a decal...yes, pics may help....
  19. A

    Trailer Set Up

    Then the bunks should be adjusted to share that load, not lots if weight on that front roller. Usually each end of the bunk board can be adjusted up and down to spread the load over the whole bunk board.
  20. A

    Bearing buddy issues

    When the bearing buddy falls off the hub, it is open, nothing to hold the grease inside. What was left of the hub had no sign of grease as it all came out at 65 mph. My hubs are and always have been inspected regularly. There was a small crack on the lip of the hub, whether it caused the...
View older results
Top