Search results

  1. B

    Cracked Block???

    Once you confirm the cracked block, I would act quickly and get a replacement ordered. If you wait to long, you may not be able to secure one easily as they may sell out. When I repowered, I had good luck with Michiganmotorz.
  2. B

    Cracked Block???

    I doubt that the Homeowners policy will cover it, it usually requires a stand alone boat policy and even with that freeze is generally not covered. Probably time to start looking for a replacement block.
  3. B

    Engines: 2 x 4.3GXi or 1 x 5.7Gxi

    The twin engines will give you better maneuverability around the dock. But you will have twice the maintenance and winterization expenses.
  4. B

    When to change bellows on a SX-A drive?

    I would go ahead and plan on pulling the drive and not just for the bellows. It is a procedure that needs to be done annually to inspect not only the bellows but also the gimble, input shaft and alignment. It`s best to catch any problems early rather than to let those parts sit in water for...
  5. B

    Should i replace the pickup coil?

    I might go ahead and replace it while you are in the area, being 21 yrs old. My experience with aftermarket parts are hit or miss. Sometimes they work just fine , but I have had some stuff that did not. Might be worth a try.
  6. B

    Cobra SX lower unit drain plug will not open

    I second the hammer powered impact driver. Make sure to get the widest bit possible.
  7. B

    Unexplained rain water on new deck boat

    You might try to re treat your cover with a waterproofing solution such as 3M`s. Also make sure that it has good support poles properly placed not allowing any water to pool.
  8. B

    Anchor advice needed for rocky and tree bottom lake

    Maybe try a box anchor.
  9. B

    Starting an engine that's been sitting...

    I`d try to run it with the gas in the tank. Try to start it at home and see if it will run before going to the lake. If it will not run right, you may have to pump the bad gas out and refill with good gas. You may get lucky and not need anything.
  10. B

    Problem with engine mount - how to remove?

    Agree with others. Remove the drive first and then remove rear engine mount nuts to allow it to move upwards. Make your fixes on the front mounts then lower back down and re-align.
  11. B

    Which Grease/Sealant between Outdrive and Bellows?

    I use OMC triple guard grease on my drive.
  12. B

    Volvo Penta GXi-E Low Power and 2 DTCs

    Your high pressure reading should be near 60.
  13. B

    First time pulling a riser with questions about condition w pics

    I know money is always a factor but if you can, I would just replace all the manifolds and risers. But definitely replace the risers.
  14. B

    Help with DPS-B 1.95 outdrive

    I sounds like you made a wise choice. For a hundred bucks more to get a guaranteed American made product, probably the better value. I think as long as you clean/change the filter screen you will not need to replace your injectors. I would just swap out the pump and try it, if you still have a...
  15. B

    Help with DPS-B 1.95 outdrive

    What did you pay for the new fuel pump? I have noticed you can buy the whole assembly on ebay for $200 these days, granted they are a knock off, but at least an option to the $1K OEM. Before I had any problems I took it upon myself to disassemble my pump during an off season and refurbished...
  16. B

    Help with DPS-B 1.95 outdrive

    The tool is for the motor only. In my opinion, you need to figure out if the stalling issues are in the engine or the drive. I think you still need to pull the drive and see why you lost so much oil. Is the drive locking up the engine or are they separate issues.
  17. B

    Help with DPS-B 1.95 outdrive

    You might consider purchasing a Rhinda diagnostic tool, not cheap but they are real nice to have. It would show any engine codes being thrown into the ECM. I bit the bullet a couple years ago and use mine frequently.
  18. B

    Help with DPS-B 1.95 outdrive

    Being that you are a quart low, there could be some drive damage as your upper gears and clutch would not have much lubrication. I would pull the drive and see if you can turn the input shaft manually. If it does not turn by hand at the input shaft, then you probably have upper end damage...
  19. B

    Will it work??

    They may be compatable. I think you will need to look at the mating surfaces of the old and the new. While basically the same there was a rubber gasket change between the drive housing and the pivot housing in that era of drives. You dont say exactly how much you are swapping, the entire transom...
  20. B

    Will it work??

    You need to tell us what model of drives you are talking about rather than part numbers. If in doubt, post pictures of the two.
Top