Search results

  1. Rranger

    1993 90hp and 1994 125hp.

    The short question is will the trim tilt unit from the 1993 90hp serial 0D237792 part number 818903A1 work on the serial 0G086789 1994 125 hp part number 824051. From what I can gather the 90hp is a two wire unit same part number as units used on 1994 125 hp but a later serial number than mine...
  2. Rranger

    Cloth or not

    I have two sheets of 3/4” plywood to laminate to the existing 1/2”, and 3/8” sheets already on the transom. Is cloth or mat necessary or not, between the 3/4” and the sheets already in place and then between the 3/4” sheets. Will be finishing with a couple three layers of Mat on the inside when...
  3. Rranger

    OMC to Volvo Penta?

    Will this OMC 350 engine bolt up to this 280 Volvo Penta drive assuming all the pieces in between are there?
  4. Rranger

    Volvo to Mercruiser

    This boat had a Volvo penta outdrive and Chrysler slant Six in it. I got a 170 mercruiser setup to go in it, would the boat motor mounts work or would they require some modification. I don't have the 170 handy to measure. I have some transom work to do obviously including cutting a new transom hole.
  5. Rranger

    Is this the aluminum head 470.

    Is this engine worth the trouble of installing? Or is this the one I read all over to stay away from. Like all according to the seller it runs good. In a 1989 Apollo boat.
  6. Rranger

    what engine

    Can anyone tell me what motor this is. Sorry about pics only ones I have.
  7. Rranger

    Outboard pod

    I have a older Sangster I’d like to put a engine pod on. I have a pod that was built for a houseboat that is 1/4” thick. I’m wondering if that is adequate to handle the torque. It would need some modification for use as a pod for my 125hp Mercury. I have a welder/fabricator lined up for the...
  8. Rranger

    Replacing transom

    And switching from I/o to outboard. I have a pod. Question is got this from lumber company about material for transom. They have marine plywood. But this is a cheaper possible alternative. Any one had experience using the below ””Yes there is but its not rated for exterior and its called fir...
  9. Rranger

    Is 125 Hp ok for this boat?

    I have this 19 ft Sangster boat and wondering if a 125 mercury OB is not to big. Can’t find anything on the net or in the boat. Had a old slant six in it? Switching to outboard. Can put a jack plate on or might cut transom and make a splash well.
  10. Rranger

    Drive swap

    Can you swap out a Volvo 250 outdrive for a 280 on the old Chrysler slant six?
  11. Rranger

    1988 Evinrude 90HP

    Hi I have a 1988 Evinrude 90HP Model number CE90TLCCA I'd like to convert it to a extra long 25 " shaft. I'm converting a old Sangster from inboard to outboard. Plan is to beef up the transom attach it to stringers ect., build a splashwell in front, and hang my outboard off the transom. But I'd...
  12. Rranger

    Gimbal bearing.

    pulled my slant six dodge engine as advised to remove my gimbal bearing. My question is after removing the engine the drive shaft pushed forward and out from rear to front. Now the bearing is in there and I’m not sure the procedure to get it out. There doesn’t appear to be any snap rings, the...
  13. Rranger

    Leak

    I'm going to look at a 20.5 ft Chapparal. It got loose from the owners dock and banged around on the rocks before he got to it and tied it up to a dock at noon. 8am the next day the stern was 3/4's full of water. They pulled it out professional mechanics did their stuff and the 80 hr engine and...
  14. Rranger

    What is this?

    My new, old, boat is basically put away hard to get at it for the winter. So I’m posting a picture of the transom and to the left of the big motor and to the right of the black cable is a round painted white fitting at the bottom of the transom. What is it and could it be my problem of taking on...
  15. Rranger

    1994 Spectrum 1850 with 90hp Mercury Force engine

    I took this boat out for the first time today and was using the bilge pump to pump out a sizeable amount of water and drained a good amount out the drain plug after getting the boat out of the water. At the back is the bilge hole which I had a plug in and another hole to the right of it facing...
  16. Rranger

    Compatible drives

    I have a 1993 Force 90 hp I just bought with a boat and when I got it home and dropped the drive oil, about a cup or two of clean water came out and then some nasty looking black oil. The boat hasn’t been in the water since Jan 2017 so I’m assuming my drive and prop shaft bearings are probably...
  17. Rranger

    Year of engine?

    A Mercury force 90HP on a 1994 spectrum pretty sure it was original on the boat when new. serial number off the tag is OE051955 It is the Mercury version has Mercury on the engine cover. Can anyone tell me the year so I can order some parts.
  18. Rranger

    Question about a jet drive

    2005 Johnson 90 HP with a jet drive. Is it as simple as drop the jet drive and pop in a complete outdrive or is there more to it? Im looking at a motor with a jet drive but would feel better if I had a backup outdrive for down the road replacement.
  19. Rranger

    What size outboard to power

    I’m contemplating buying a 1977 267 Reinell Sedan Cruiser, OMC Cobra 351. It’s 26 ft, pic attached. I have a heavy duty outboard bracket and plan on ripping out the OMC stuff and installing the bracket and putting on a outboard engine, question is what size outboard will it need. If possible...
  20. Rranger

    Yamaha blocks

    I have a 2001 Yamaha 200HP HDMI. Anyone know what year and size blocks 225HP possibly are interchangeable? Thank you.
Top