Search results

  1. salvageyard saviour

    Hardtop repair

    Thanks for the reply, I was joking about the flex seal. What type of glass should I use? It's not structural, so CSM ? How thick ?
  2. salvageyard saviour

    1972 Grew SS245

    Okay, maybe 300. They're not double humps but a 71 225 hp SBC shouldn't be hard to get a few dollars from.
  3. salvageyard saviour

    Hardtop repair

    How can I repair these cracks? My lazy self wants to sand and apply flex seal.
  4. salvageyard saviour

    1972 Grew SS245

    Don't know if that cover is "lipstick on a pig " but don't give up on it yet. Check the stringers! Try to remove the lag bolts holding the mounts to stringers. If they just spin, you have rot. Personally I love boats like that. That electric shift will have people talking at the ramp. Just...
  5. salvageyard saviour

    Any Archers, archery hunters here?

    By the way, those aren't trailcam. Love the challenge of getting close, and my friends laugh at my military surplus camo.
  6. salvageyard saviour

    Towing boat with snow mobile!

    🤣🤣🤣 so true!
  7. salvageyard saviour

    Any Archers, archery hunters here?

    These old shoulders can't do a compound anymore. Love the crossbow! I only hunt from the ground and the shorter limbs are convenient. Last spring while turkey hunting, this guy was fun to watch! this might have been him the fall before as a button.
  8. salvageyard saviour

    Towing boat with snow mobile!

    That video sure makes me feel old and soft 😭 In my 30's That would have been fun, also the reason 1 of mine was an outboard. But now if the wind blows more than 10 mph, I don't go on the water. Justifying it as "older and wiser " Good news is haven't had to hail the C.G. in 20 years! Not...
  9. salvageyard saviour

    OMC Stringer 3.0 belt replacement

    At least Merc engineers had the forethought to put a spacer between the mount and block. I assume just for this.
  10. salvageyard saviour

    Mounting transducer near outdrive?

    Thanks for the reassurance 🤗 Agreed, doubt it'll matter and it'll be easier to route the cables from the same place. I just got rid of all my older Impulse units, nice equipment but bulky. Can't even find those combo ducer/speedo on eBay anymore. Or the heads w/o Loran. Thanks again
  11. salvageyard saviour

    Mounting transducer near outdrive?

    Thanks Bondo, I read that when you replied to someone back in 2012 or 14 I think. At trolling speeds, were you happy with the sonar quality? Do you think the temp/speed wheel would be better on the port corner? It would be more protected in close with the transducer.
  12. salvageyard saviour

    Mounting transducer near outdrive?

    A Mercruiser, I could see possibly a collision. This Electric shift is 8 inches from the transom and doesn't pivot from a gimbal or trim in. Transducer is 3 inches, can't see how they can make contact. Do bubbles really have an impact at trolling speeds? This isn't thru hub exhaust.
  13. salvageyard saviour

    Mounting transducer near outdrive?

    Hope this isn't like an oil or efi topic, so here goes. My Bennett trim tabs gives gives very little choice for a transom mount skimmer. I want to put it between the outdrive and tab. Also want to put temp/speed wheel somewhere. Maybe outside port tab like starboard stuff. I've read...
  14. salvageyard saviour

    Installing electric downriggers?

    Need advice on connector type at transom and if I should wire directly to second battery or battery switch. Has upgraded higher amp alternator. 1-2-both-off switch and diode charge isolator Riggers are old obsolete Walkers (I know, but they work 😲) I have an obsession with old stuff. Have...
  15. salvageyard saviour

    Electric shift coupler

    Kenny, Similar question about intermediate driveshaft. A new to me 1968 210 hp TUE-17R. I can feel slop when I twist the intermediate ball gear. Feels like wear in the coupler. Will I need a coupler like this? Also the driveshaft is listed as a one piece shaft and gear (can't find one...
  16. salvageyard saviour

    Electric shift coupler

    I'm trying to go the other way. Hoping to use it with a 78 SBC 350. I carefully drilled holes in the 78 flexplate also had to shim crank pilot hole. Was curious if this was a stock item or customized.
  17. salvageyard saviour

    Electric shift coupler

    No idea, I assume mid - late 60's because of the small journal crank bolt pattern
  18. salvageyard saviour

    Electric shift coupler

    Has anyone seen a coupler like the one on the left? Spline count is the same in both. Believe it came off a small journal SBC. Also it was attached to a flexplate not a flywheel.
  19. salvageyard saviour

    Do you use non ethanol gas ?

    What's shelf life? Earlier this year, I drained 40 gallons of 20 year old gas from parts boat. Been mixing 50/50 With fresh. Running log splitter and mowers no problem. Last year used 10+ yr old gas mixed 50/50 in 91 F350, ran fine. Imho, old gas can be used, just have to get used to the...
  20. salvageyard saviour

    Dual battery switch and isolator

    It's still going to full output. Going to wire single battery, no switch, no isolator. Something wrong with voltage sense, so I'll see if it's somewhere else in the system and not the dual battery stuff.
Top