Search results

  1. C

    Need help with 1968 1.5 HP Johnson model SC-10S

    old style carb going back to the 60's idling sucks gas from the top of the carb so that works :) higher speeds suck gas from the HS nozzle feed by the bottom HS needle. Have you tried openning up the HS needle a bit left (counter clock wise) ? Or... try closing the needle a bit in...
  2. C

    Evinrude Etec 2012 150HP motor power tilt and trim stuck in down position

    good luck .. see your PM
  3. C

    Johnson TN-26 Fuel Mixture

    yes pretty certain... drop him a PM here and on the AOMCI site not certain but I think some folks have used o-rings ( find and fit them to size you may be ok )
  4. C

    Evinrude Etec 2012 150HP motor power tilt and trim stuck in down position

    maybe.. this may help
  5. C

    Evinrude Etec 2012 150HP motor power tilt and trim stuck in down position

    Also check-in with these folks .... dedicated to ETEC support http://www.etecownersgroup.com/?forum=115573
  6. C

    Johnson 50hp Not cranking normally

    After checking the neutral switch if the problem still persists put the key on START and have a buddy wiggle the wiring all the way back to the engine . check any connectors for oxidation
  7. C

    Johnson TN-26 Fuel Mixture

    try removing the sintered filter for a test ... or you can install a small round filter for lawn tractors or similar on a temporary fuel line.
  8. C

    Johnson TN-26 Fuel Mixture

    it is a general T model document from the johnson service manual
  9. C

    Johnson TN-26 Fuel Mixture

    easy to clean ...
  10. C

    Johnson TN-26 Fuel Mixture

    I never started mine up but I think they are a bit finicky to adjust have you openned up the LS needle or anything else to get the fuel to flow in the carb. recheck the float but I suspect it is OK being an upside down inlet needle ..check side clearances in case it does snag in...
  11. C

    tether switch

    basic diagram
  12. C

    TN26 5hp Johnson upper crankshaft seal replacement

    info is from the Johnson manual which you should get a copy to service your oldy (oldies)
  13. C

    TN26 5hp Johnson upper crankshaft seal replacement

    see info on slinger on a CD
  14. C

    1954 Johnson CD-11 5.5 hp

    see my post #3... it says VISIT AOMCI ask a member .... so you must to :) https://www.aomci.org/forums/forum/ask-a-member-d1/ if you plan working on oldies the book itself is worth it annual membership $$$ depends on country of member
  15. C

    1954 Johnson CD-11 5.5 hp

    top of the screen just on the left side of MEMBERS BENEFITS in RED but maybe..if you are not a paid member the screen may not display it
  16. C

    1954 Johnson CD-11 5.5 hp

    hurry... if you need them https://www.ebay.com/itm/203247943567?hash=item2f52857f8f:g:6JEAAOSwbH9f~59a
  17. C

    1954 Johnson CD-11 5.5 hp

    here you go http://www.leeroysramblings.com/johnson_magneto.htm http://www.leeroysramblings.com/johnson%205.5hp.html visit the aomci "ask a member" site dedicated to keeping oldies running as a member you would have free access to the download of the Johnson manual aka "RED book"...
  18. C

    Early 70s evinrude wire diagram

    in here maybe... https://maxrules.com/JOwireindex.php https://maxrules.com/graphics/omc/wiring/100-125_1971-72.jpg
  19. C

    1966 9.5 Evinrude won’t start.

    see pic. not a big job
  20. C

    Magneto experts needed ('68 Johnson 9.5hp top cyl intermittent spark)

    Another happy ending :-) thanks for your feedback !
Top