Search results

  1. C

    1972 johnson 25 hp ignition points

    the actual gap isn't all that critical. the timing of the openning is critical see video. .020 is a ballpark using the high point of the cam just adjust the gap openning " time" per video
  2. C

    1994 Evinrude 140 water pump question

    download this one free it likely has all you need and more. https://drive.google.com/drive/folders/1-pyBmXzRaZ16y9sJ1QkSfjnBGwA-HzsB
  3. C

    1994 Evinrude 140 water pump question

    just disconnect the cross pin holding the shift rod near the PH (on the side) models vary .. do not turn (unscrew or screw the shift rod.. keep it aligned when replacing
  4. C

    1962 evinrude fastwin 15036 fuel issue

    the bulb does not stay firm so that is not the problem it is only used to fill the carb then the fuel pump sucks up what it needs. hard to belive 6g/hr burn rate fine for a 50hp carbed Merc WOT pulling skiers but not a 10hp in a barrel !! oily barrel water is fine not an issue 2...
  5. C

    My new project.1972 johnson 25e72r .

    wrap it up with waxd dental floss... or similarcotton thread
  6. C

    1997 Johnson 9.9hp 4 stroke electric start intermittent spark

    see manual same time period may help you or not... J&E being cousins and all.... https://drive.google.com/drive/folders/1-pyBmXzRaZ16y9sJ1QkSfjnBGwA-HzsB
  7. C

    1997 Johnson 9.9hp 4 stroke electric start intermittent spark

    this... may help
  8. C

    My new project.1972 johnson 25e72r .

    Iboats folks likely have parts or visit https://www.marineengine.com/parts/johnson-evinrude-parts.php?year=1972&hp=25&model=25E72R&manufacturer=Johnson&section=CARBURETOR
  9. C

    1962 evinrude fatwin 18hp carb settings.

    happy ending... your good for another 20 years if you pamper it..and oil it !
  10. C

    Evinrude 1972 18 hp fastwin not pumping much water

    1962 15036 ... similar to FD16 download this bible to service your oldy https://www.socalaomci.com/library/johnson_service_manual_10th_edition.pdf
  11. C

    Evinrude 1972 18 hp fastwin not pumping much water

    make certain water tube grommet does not block the small holes in the pump housing . make certain holes are clear so what do you have 62-63 72 post model number !!!
  12. C

    Etec 75 hp

    looks nice but does not change engine performance :) why ??? who knows... engine shows general lack of care .. heavy salt deposits externally owner propably never did flushes inside and outside the engine ...proceed with caution is what I would do. it may be a gem or a rock
  13. C

    Etec 75 hp

    no expert on boat performance but 75hp ETEC known to be 10% underrated so you would have about 82-83hp to push your rig... not much difference big big savings of $5G fuel low oil consumption NO SMELLY OIL using xd100 great torque ... consumes .6L/hr trolling and the early ones actually...
  14. C

    Key won’t crank like it’s not in position

    glue ? :)
  15. C

    Etec 75 hp

    first thing to do is check in with the folks at the ETEC owners board and submit your question for ETEC experts to comment. Board has an excellent search engine https://www.etecownersgroup.com/latest your 2004 is 22 years old with very little use if the EMM is the original one that came...
  16. C

    1962 evinrude fatwin 18hp carb settings.

    fyi
  17. C

    1962 evinrude fatwin 18hp carb settings.

    no need for a "timing tool" see video a plain VOM works fine .. At START the cam follower on the carb should line up with the bar on the cam under the mag plate. "coil gap" is the same .... just run your finger nail up-down the face. if it snags going up or down adjust coil position
  18. C

    1962 evinrude fatwin 18hp carb settings.

    Never had an issue myself if the back screw is just release a bit to allow rotation adjustement & as a means of reducing excess torquing on the pivot screw. As per video a recheck of alignment when done confirms all OK .
  19. C

    Evinrude 50 4 stroke 1999 been setting, need to restart suggestions/ guidence

    some pumps... have ben known to be revived on ETEC engines by short reverse polarity kicks and feeding the pump some oil.. let it soak and retry inverse polarity kicks... then forward polarity some have even boiled the pump (in a plastic bag) but I never tried it myself. injectors can...
  20. C

    1962 evinrude fatwin 18hp carb settings.

    suggest you download the manual I provided a link to see post #6 it contains all the info you need. condensers may be ok but at least it needs a basic OHM test and capacitance ...with a capacitance equipped VOM ... refurbing an oldy involves parts which can add up to $100+ so figure...
Top