Search results

  1. M

    Yamaha 50 hp 2 stroke prop seal depth

    Replacing the prop seals on my 2006 3 cylinder 50 hp. Currently the outermost seal is 4.5 mm recessed from the outer edge of the housing. Should I repeat that or install deeper? I'm aware there are 2 seals there. Should I push the 1st seal all the way down and then the 2nd seal all the way down...
  2. M

    Honda 9.9 burning oil

    Yes it is good to go. Ultrasonic cleaned carb got rid of bog. Oil issue gone. I think former owner stored it on the wrong side. Thanks for everyone's help
  3. M

    Evinrude 9.9 carb question

    Ok
  4. M

    Evinrude 9.9 carb question

    You are correct sir. Just strange to me why the same cover could use 2 different needles. Looks like one of them would be too short to allow the mixture knob to connect?
  5. M

    Evinrude 9.9 carb question

    Yes I've seen that. A little confused why it comes with 2 needles though.
  6. M

    Evinrude 9.9 carb question

    Ok I'll revisit the carb and check it out. Thanks
  7. M

    Evinrude 9.9 carb question

    Yes a new #21 is installed. I need to take a look at the cover I used. Maybe there is no way for air to enter the top of the carb?
  8. M

    Evinrude 9.9 carb question

    Working on a 1988 evinrude 9.9. Plastic top carb. Original top was cracked. I installed one that looks just like the updated kit which uses a plastic nipple in which to slide the throttle roller onto. I transferred the needle valve from old to new (this version uses a front mounted mixture...
  9. M

    Honda 9.9 burning oil

    Is this similar to a car where I can pressurize the cylinder through the spark plug hole then change seals? No need to pull cylinder head right?
  10. M

    Honda 9.9 burning oil

    Thanks. Know of any good write up about how to do the valve seals? Why the thermostat test?
  11. M

    Honda 9.9 burning oil

    Why don't you think it's burning oil? What about the fresh oil I'm finding in the breather hose and airbox screen?
  12. M

    Honda 9.9 burning oil

    New to me 2008 9.9 Can't get it to accelerate without big bog that will kill the motor if not turning back throttle to idle. If you turn throttle slowly it will rev up but blowing smoke out exhaust. I cleaned carb thoroughly. Found engine oil in airbox on that screen looking part. Pulled spark...
  13. M

    Nissan 30 hp 2 stroke tiller kit

    Thanks. Just what I needed to hear
  14. M

    Nissan 30 hp 2 stroke tiller kit

    New to me late 80's? Nissan 30 hp 2 stroke. Want to make it a tiller style. Anyone know what's in the kit part number 372S630001 Got the part number from boats.net. it's a tohatsu kit but should be right for my Nissan.. thanks Serial number NS30 A3. 346-b1.
  15. M

    Identify this fuel guage

    I guess I'm mostly concerned about the guage working with current sending unit. Is that something I need to know before buying a new guage?
  16. M

    Identify this fuel guage

    Fuel guage in my 1997 wellcraft 190ccf Need to replace due to fogging when humid out. Trying to get the same one so I can keep the same sending unit. Thanks For some reason it won't let me upload the picture
  17. M

    Mariner 30 hp oil injection delete

    Is there a way to check if oil is being delivered?
  18. M

    Mariner 30 hp oil injection delete

    Yeah you are probably right. I guess I'll keep it
  19. M

    Mariner 30 hp oil injection delete

    Got a 1996 mariner 30 elo (2 cylinder single carb with oil injection). Looking to remove oil system and mix manually. Anyone know the procedure to do this? Can I leave the oil pump attached to the block? Just disconnect and plug oil pump lines? Will there be a warning system that needs to be...
  20. M

    9.9 hp yamaha 4 stroke crank pressure

    I'm afraid to put oil in it and try to start it. I don't want that pressure to go blowing oil out of the dipstick hole. Something doesn't sound right with that area being pressurized but how come it made good compression?
Top