Search results

  1. M

    2003 Mercruiser 8.1 HO No Crank No Start Fuel Pump Running

    Yes I do, I was checking power with a voltmeter
  2. M

    2003 Mercruiser 8.1 HO No Crank No Start Fuel Pump Running

    One place I haven't checked power at is the neutral safety switch. I'm just getting 0 voltage at the yellow/red wire going to the starter solenoid from the solenoid that's mounted under the ECU. Changed it out for a new one and I was still having the same issue with 0 voltage with key turned in...
  3. M

    2003 Mercruiser 8.1 HO No Crank No Start Fuel Pump Running

    Well, I still the same issue. No voltage at the wire going to the solenoid. I checked voltage going to the ignition switch, cannon plug terminal, 50 amp breaker, and starter pilot relay and it has enough voltage. The solenoid that the starter solenoid wire runs to has no voltage at the starter...
  4. M

    2003 Mercruiser 8.1 HO No Crank No Start Fuel Pump Running

    Got it all sorted, I ran the wire back to the starter solenoid 8M0185149. No voltage at the wire connected to the solenoid when ignition was turned to start and no voltage at the solenoid where the starter solenoid wire connected. Thanks for all the help!
  5. M

    2003 Mercruiser 8.1 HO No Crank No Start Fuel Pump Running

    Got it all sorted, I ran the wire back to the starter solenoid 8M0185149. No voltage at the wire connected to the solenoid when ignition was turned to start and no voltage at the solenoid where the starter solenoid wire connected. Thanks for all the help!
  6. M

    2003 Mercruiser 8.1 HO No Crank No Start Fuel Pump Running

    Hello, I'm having an issue trying to start my engine on a stand. There's enough juice in the batteries. Cranks and Starts when the starter is jumped. Fuel pump turns on when the key is turned. I changed out the starter relay with a new one and still the same issue. I've used this ignition...
  7. M

    Volvo Penta 7.4 GL Slight Water in Oil

    I got my problem sorted out, looks like it was condensation coming in from carburetor. Looks like it had water in the fuel. Have it plugged up to non ethanol and after running checked inside the carburetor and intake and it's dry. Manifolds and Risers are still bone dry. It was hardly even...
  8. M

    Volvo Penta 7.4 GL Slight Water in Oil

    Thank you sir!
  9. M

    Volvo Penta 7.4 GL Slight Water in Oil

    I understand, I have a set up already to run engines out of water. I'm asking in regards to having that set up having a control box with gauges hooked to it so I can check temperatures and pressures. I have a rigged ignition and key to run engines all day.
  10. M

    Volvo Penta 7.4 GL Slight Water in Oil

    Do you have the milwaukee one? If you can share what you use that would be great. I primarily work on cars but have had no need on them since I work on only a specific few makes and models and the issues are all the same on them. Boats I have worked on for a few years but as far as water in oil...
  11. M

    Volvo Penta 7.4 GL Slight Water in Oil

    Do you know if they sell any kits to run engines out of the boat by chance? Oil pressure, temp, water temp gauges and perhaps a control box to increase rpms? Would it work if I increased the rpms on it with a throttle cable and shifter to get it up to temp?
  12. M

    Volvo Penta 7.4 GL Slight Water in Oil

    Luckily dry as a bone with the risers pulled. No rust marks or signs of water intrusion there.
  13. M

    Volvo Penta 7.4 GL Slight Water in Oil

    I did not change it myself, the previous owner changed it. I'll change it out one time to make sure. It's out of the boat so a bit difficult to get it to run up to temp on a pallet since I don't have gauges installed. It's fresh water. I have not inspected anything as of yet. I was looking at...
  14. M

    Volvo Penta 7.4 GL Slight Water in Oil

    Any suggestions on what to check and how to check where the water is coming in from? Oil is not milky at all aside from a small streak of white on the dipstick which is hardly noticeable. I'm not sure if its condensation or what it was. Should I start with pulling the risers to see if there's...
  15. M

    Kohler 5e generator standalone starting

    Can anyone point me to videos/instructions on how to start a Kohler generator on a table? Where power should be to keep it running? Aside from the starter motor and ground. If there is any machinery/equipment recommended as well to be able to put loads on it that would be great. I have several...
  16. M

    Yamaha F300 Cylinder Head Pressure Testing

    For pressurizing the cylinder head to check for cracks and leaks. Same way as you would check with any other cylinder head. I just have not found any where that sells them and/or can make them. One shop I have found had one custom made but they do not recall what shop it was since it was years ago.
  17. M

    Yamaha F300 Cylinder Head Pressure Testing

    Yes, that's exactly what I'm looking for. To make sure I don't have any cracks and leaks.
  18. M

    Yamaha F300 Cylinder Head Pressure Testing

    Can anyone give me any directions as to where I can buy pressure test plates for Yamaha F300 cylinder heads?
  19. M

    Looking to buy 1x Used 2016+ Yamaha 300XCA

    I'm looking for one Yamaha 300XCA with under 700 hours. Preferably counter rotating as I just bought a standard rotation 300. I've looked on Boat Trader, eBay, and Facebook marketplace and so far not much luck other than higher hour engines. I'm looking for recommendations on where else to...
  20. M

    Where to Find Kohler 5E Generator Motor Mount / Fuel Pump bracket

    Generator is pulled already, really the worst worst was that bracket being disintegrated and the drip pan as well. The rest of the boat was in solid condition. The engine hardly had any rust. These pans are known for rusting. I have had 6/7 Boats with them. Only one purely freshwater boat had...
Top