Search results

  1. Eddie Rivera

    No spark

    Re: No spark Get your self a manual it's my best advice. Per my experience from yesterday and even last year, check all wires make sure they are not loose nor rubbing on the chassis like mine the ignition coil and module pack was tight and pressing on 2 cables grounding it self even though I...
  2. Eddie Rivera

    89 Force 50HP turns on and stays on only on high idle start

    1989 Force 50 HP 507X9B I mixed a gallon of fresh 91 octane and 2.6 oz of oil and 1/4 can of sea foam to decarbonize the motor since I have not turned it on for almost a year - on a carburetor with a new main niddle, a new float and gaskets and let it sit there and run "with the motor cover...
  3. Eddie Rivera

    89 force 50 HP how to adjust new float with new needle

    Re: 89 force 50 HP how to adjust new float with new needle I just want to share with everyone the exact problem/reason why my motor had weak spark and fuel and would not start though it would simply crank. It was the ignition module wires going to each coil pressed against the screw on the...
  4. Eddie Rivera

    89 force 50 HP how to adjust new float with new needle

    Re: 89 force 50 HP how to adjust new float with new needle Okay guys we really did it this time --- one of you guys gave me a blog from Last year where I my self wrote that when I pushed on the packs it would turn off -- I wrote that and that was the problem again - Two things were happening...
  5. Eddie Rivera

    89 force 50 HP how to adjust new float with new needle

    Re: 89 force 50 HP how to adjust new float with new needle These are the after lapping pictures. I did it 3 times. Added the compound to both and I put the flywheel on it with no key and I moved the wheel back and forth grinding and cleaned it up and then I did the groove where the key goes on...
  6. Eddie Rivera

    89 force 50 HP how to adjust new float with new needle

    Re: 89 force 50 HP how to adjust new float with new needle These are the before I lap pictures. I tried the key on the shaft and it does bit fit snug and does not stay on by itself. It fits better than the old one obviously but how do I make it stay when I clean it off and re-install the...
  7. Eddie Rivera

    89 force 50 HP how to adjust new float with new needle

    Re: 89 force 50 HP how to adjust new float with new needle Got my FlyWheel key, got the valve grinding compound and got me a timing light.
  8. Eddie Rivera

    89 force 50 HP how to adjust new float with new needle

    Re: 89 force 50 HP how to adjust new float with new needle
  9. Eddie Rivera

    89 force 50 HP how to adjust new float with new needle

    Re: 89 force 50 HP how to adjust new float with new needle
  10. Eddie Rivera

    89 force 50 HP how to adjust new float with new needle

    Hello, replaced float, needle, bowl gasket, and both small washer/gaskets on the screw holding bowl. Motor will not start. bulb gets hard and no leaks. motor cranks but wont start. After changing the exhaust gasket and messing with float it started 3 times only till it died and never turned...
  11. Eddie Rivera

    89 force 50 hp hard to start after exhaust gasket change and carb gaskets

    Re: 89 force 50 hp hard to start after exhaust gasket change and carb gaskets ok i installed the new needle and adjusted the float the best i could and did the starting procedure you mentioned, the bulb did get hard, no fuel leaks any where, fuel did come out when i did the choke and my motor...
  12. Eddie Rivera

    89 force 50 hp hard to start after exhaust gasket change and carb gaskets

    Re: 89 force 50 hp hard to start after exhaust gasket change and carb gaskets these are the pictures of my findings, as i said although that little peace is broken its able to be adjusted. i never had any issues with it starting till i did the float adjustment even with the needle as it is...
  13. Eddie Rivera

    89 force 50 hp hard to start after exhaust gasket change and carb gaskets

    Re: 89 force 50 hp hard to start after exhaust gasket change and carb gaskets
  14. Eddie Rivera

    Help - 89 force 50 HP float settings

    Can anyone please help me determine the measurements to set my carbs float? Both normal operating position an upside down? How to measure it and with what? My seloc is too general an I think I used the wrong motor settings. My model # is 507X9b - remote controls single carb. Please help
  15. Eddie Rivera

    89 force 50 hp hard to start after exhaust gasket change and carb gaskets

    Hello and thanks to everyone who helped me change my exhaust gaskets and carb, after several months its finally done. I have a problem --- it has a hard time starting. My model of outboard is 507X9B and i changed all my fuel lines out and in and on the carb i changed the 2 small gaskets that go...
  16. Eddie Rivera

    89 Force 50 HP need re-assembly help

    Hello friends, I finally took the motor apart for the exhaust gasket replacement. I used that JP blaster as instructed by you guys, however at the plate where the motor sits, most of the bolts or screws were relatively loose had lots of anti-seize grease, I'm afraid this was one of the causes...
  17. Eddie Rivera

    89 Force 50 HP- HELP exhaust gaskets replacement

    Re: 89 Force 50 HP- HELP exhaust gaskets replacement Good morning Jerry! I just read your response. I already removed the flywheel yesterday along with the coil packs and the starter. Disconnected the ign coil too. DISCOVERY: my model is a H0507X89B : The lower starter bracket was off cuz the...
  18. Eddie Rivera

    89 Force 50 HP- HELP exhaust gaskets replacement

    Hello guys, I'm back I had to take a brake from working on my boat - I got burnt out. I've started working on it now and need help. 89 force 50 hp I need to replace exhaust Gaskets. Ontario - Southern California (inland empire) Please help me with instructions on how to do it. Any special...
  19. Eddie Rivera

    89 force 50 hp wastes and squirts fuel

    look at the picture with the red mark - am i missing a cap?? 89 Force 50 HP wastes too much fuel and I increase the throttle it squirts fuel from end at bottom- where the carb meets the block. Also at high speeds it squirts from the small plugs and leaks out a lot from the lower bowl and it...
  20. Eddie Rivera

    89 force 50 hp need to replace exhaust Gasket

    89 force 50 hp I need to replace exhaust Gaskets. Please help me with instructions on how to do it. Any special tricks anything to watch out for anything I should not do. The very hard to find kit came with 3 gaskets. Where can I find a tool to hold the fly wheel while I loosen up the too nut...
Top