Search results

  1. Benny1963

    d hadley please

    hey mr hadley as ya know i have the mckee with the . 175 crossflow .got it turning 5500 with 21 p no cupping no blow out probs need some stern lift should i run a 21 p cupped and slowly move my motor up till it cavs or looses water pressure then take it back down a little ,cant trim up with out...
  2. Benny1963

    brass thru hull conector?

    does anyone have a link or place that i can order brass drain thru hull for mckee type hull 3inchs or so
  3. Benny1963

    1979 mckee 17ft help with thru hull connectors

    my mckee has two thru hull drains that are brass they are 3 or so inchs long do i use plastic or can i get the brass and if so whats with the install on the brass? thanks for any info
  4. Benny1963

    above waterline exhaust question

    thinkin of useing bobs machine weld on exhaust that fits on mid that has the plugs to quite if needed ,article says works well with stock motors , mine is a 1983 evinrude crossflow 175 with boysens and xp heads and some jetting for the boysens anyone know anything about them hadley /bullett ?
  5. Benny1963

    hey guys help with prop?

    i have a restored 17 ft mckee craft whaler type hull im running a 14x21stainless no cupping left on it omc prop, my motor is 1983 175 evinrude crossflow fresh and tuned my cav plate is at bottom of hull flush ,im turning 5000 rpm at 42 mph . i cant trim up or i get bow hop before i can get to...
  6. Benny1963

    top coat ?

    i have a 1979 mckee bottom is gelcoat white ,top is aqua or light blue want to repaint topside want to use the easiest method and type of paint .any suggestions on paint and or links to topside paint,i can spray ,but would rather roll and tip but want good finish ,any input would be great thank...
  7. Benny1963

    tach rewire

    im going to wire past the rubber connector on my control box for my tach can yall tell me what the wire colors in control box are for the tach such as sender/ ground / and ignition .my tach has gray for ground red for ign and white for send any help or diagram would be great, my seloc is...
  8. Benny1963

    motor height ?

    i have a 14 1/4 x21 on my evin 150 it porps before i can trim up to get the extra rpm will raising motor help gain rpm or help with porping its currently level with bottom of keel . but i cant trim up because of porping i need anopther 800 rpm
  9. Benny1963

    power trim prob?

    1983 evirude 175 older three wire trim . trim has new relay and wires and trim control switch on steering motor is suspect , when i use my transom saver it seems to stick after i remove it and go to trim down . my down trim is faster than my up but it should be the other way around up uses...
  10. Benny1963

    prop probs 175 evin

    ran my boat today ran 5200 rpm no gps speed today boat responds to trim but cant get enough trim due to porping 14 1/4 x 21 no cupping older prop motor is tuned and running great it stainless , on a 17ft mckee hull its dry and mint condition. do i need to run some smart tabs and try to trim...
  11. Benny1963

    hey ems help tach wireing

    tach connect at control is shot do i need to cut into harness and find wires up front then rewire to tach .or come all the way from the back ,and wire a hot from bat and ground to fuse block with ign hot only and constant hot for lights and run my signal wire forward to ?
  12. Benny1963

    tach rewire question

    hi everyone i have a 1983 175 evin my tach is wired thru control ,i need to move the wireing direct to motor because of damage to connector at controls tell me if this is right ,grey wire to grey at rectifyer ign wire to key only hot at selinoid and ground to battery ground if not right...
  13. Benny1963

    hot foot trim at floor

    was wanting to know if any of you have used the hotfoot trim swicth good or bad input would be great , thanks
  14. Benny1963

    hey laddies help please

    how are yall doing here on the dark side i have a 1977 merc 500 or 50 . after building carbs and changing stator and timer base it runs good just dont know how to idle it up seems the only way is to adjust throttle cable can anyone run down the idle adjustment to me i havent worked on any of...
  15. Benny1963

    any body got good 700r4

    i just put a rear end in my tow truck for boat. 373s but i have 30 inch tires well with turbo 350 its ruff on gas plus has stroker motor ,want a 700r4 the guys around here cant get im to stand up long dont want to spend 1500 for custom trans .anyone with some info or info on 4l60 e swap let me...
  16. Benny1963

    one for the gurus trim tilt.question

    alright i have fixed my trim and added the switch to steering . i have a three wire system the up motion runs through a selinoid but the down motion is straight from the switch making the downward draw through switch. my boat mech told me to add selnoid and run the down motion through a...
  17. Benny1963

    control cables

    well guys got my trim fixed went to run my boat and my motor doesnt pull back to idle i believe my control cable is stretched and my gear select cable sheating broke wheres the best place to get cables quick and what should i buy regular or hi po i may go with hot foot i put my trim on...
  18. Benny1963

    mr hadley help please

    1983 evin 150 crossflow. i see the exhaust kits on scream and fly that go on back of ex houseing. that lets free flow of exhaust above waterline it can be plugged with rubber plugs to close it off .any thoughts on these i would like to try one it would be neat to get that ex sound and be able...
  19. Benny1963

    after ike all well?

    hi everyone i know a lot of you are from texas . dont know ya face to face but kinda know whos who . hope yall are well ,just got hit here with gustav in livingston la. ike didnt do much to us .But i know it tore up texas .wish ya a speedy recovery and good weather .im from beaumont been in...
  20. Benny1963

    trim issues 1983 175 evin three wire system

    well hello every one. built my motor now my trimm is out . who would have thought that ,lol its a older three wire system with single relay . It will go up but not down .relay is clicking when it gos up I havent isolated the wires and jumped them , my seloc manual has horrible diagrams ,can one...
Top