Search results

  1. Benny1963

    a few question evinv6 1983 175

    hi everyone , i am putting my fresh 175 crossflow powerhead on .well im pretty much finished .ineed primer line the small line from my primer line to my tee in the hose ,does anyone know what size it is it is small and needs to be gas proof ,can this be obtained localy at parts store .secondly...
  2. Benny1963

    motorcycle dial indicator dhadley

    hi mr hadley i have dial indicator with base for my tdc marks but i saw on reggie 8s post that you use a motorcycle dial indicator that screws into plug hole any idea were to get one possibly local also do they come with adapters for different plugs or is there a common size my motor is 1983...
  3. Benny1963

    d hadley help please evin 150 crossflow timeing setup

    i need to set my timeing pointer on my 1983 175 evin crossflow i will use a dial indicator to do it insted of pisto stop can any one give me th run down on useing the indicator instead of piston stop , i take it that you set it up on number one zero it and rotate fly wheel till it reads the...
  4. Benny1963

    hi guys 135 or 140 looper

    im looking to build a 140 looper olderone if i can find one whats the best year and model to mod ,or 135 dont know what years are the older one ,just looking for one older motor to mod a looper
  5. Benny1963

    mr hadley

    what rpm can a1983 175 evin v6 crossflow run to . with boysen and small mods without self destructin. as in rotating parts and still make hp
  6. Benny1963

    ground wire ?

    im putting a 150 1981 evinrude v6 back together [powerhead replacement] i took pictures and have diagram .but i have one 3 inch black ground wire that i dont know were it goes the motor is wired all coils have grounds the ground from the bumper braket to the pan bolt is on ,the regulater is...
  7. Benny1963

    how fast /new powerhead /

    i know theres no way to tell without certain detail i have a 17ft mckee 1981 hull is dry and slick fresh gelcoat its rated at 140 hp i have a 150 mid with a fresh 175 crossflow powerhead, tuneing is near perfect havent pulled up the rpms yet due to break in . i had the 150 powerhead on it the...
  8. Benny1963

    hi v boat lower oil in a car

    put used open carrier 12 bolt rearend in my work ride need to top off rear does the hi vis gear oil for outboard lowers work in automotive ap. save me a trip to buy a quart when all i need is a couple of ounces my concerns are will it blend with coventional gear oil 80 90 thanks
  9. Benny1963

    shift shaft leak

    have been getting a little water in lower . pressured it up today and its bubbling from my shift shaft seal 1983 evinrude 150 ,the diagram on evinrude only shows a shift shaft cover gasket , and and o ring underneath is that all there is there to leak looks easy enough .if any one knows what...
  10. Benny1963

    static timeing without carbs on joes method

    im waiting for some carb kits i want to set my timeing pointer and use joe method to time my 1983 150 crossflow.can i do it with out carbs on everything else is finished except lower that im have some work done on . wanted to get the inital wot timeing set . then build carbs and link and sink
  11. Benny1963

    happy memorial day to all those that served

    to all that have served do serve and will serve in the future . and the people and familys that support them and our country . happy memorial day you should be proud , Highest regards Bennyb , MAY YOU ALL BE SAFE,
  12. Benny1963

    1983 evinrude 175 flywheel torque

    hey guys got my flywheel on and torqued to 120 ft lbs cant hold it to get the 140-145 needed do i need a flywheel holder or is there homemade solution. thank you
  13. Benny1963

    how fast with proper engine set up

    i have a 1980 mckee [whaler copy ] 17 ft hull is dry and slick running at 5800 wot 1983 evinrude 175 boat rated at 140 , it was running 47 mph with scored cyl and bad wrist pin bearing, with the 150 powerhead ,its know evin 175 powerhead tuned well what king of speed can i expect, and better...
  14. Benny1963

    can i paint or clearcoat my flywheel

    was wondering can i paint or clearcoat my fly wheel or will there be heat tranfer prob from painting the aluminum
  15. Benny1963

    1983 evinrude 175 flywheel torque

    have lapped my fly wheel and going to reinstall my manual specs 140 to 145 ft lbs is this correct seems like a lot a few people told me 85 ft lbs .also i have no timeing sticker for my wot timeing the manual says use sticker on my model my 150 was 28 degrees is the 175 the same 1983 evin175...
  16. Benny1963

    another flywheel question;sorry

    posted a few minutes ago but forgot to ask question. 1983 175 crossflow on my flywheel there are timeing marks for number 1 cyl and number 2 cyl i know i time it off number 1 marks and cyl what are the number 2 cyl marks for thanks
  17. Benny1963

    powerhead bolt kit

    evin150 1983 crossflow i cant seem to find a powerhead to adapter plate bolt set
  18. Benny1963

    fuel clamps ?

    im trying to find some fuel line straps.local so i wont have to wait to get brp to send them or order from a speciality distr. was hopeing some one new of something from a auto store or anthing they have used from local places want to do my fuel sys but want the right tie straps or something...
  19. Benny1963

    hey laddies

    can i use wheel bearing grease as a subsittute for anti seize on powerhead bolts to adapter also do you suggest a dry gasket between powerhead and adapter thanks bennyb
  20. Benny1963

    hey guys antiseize substitute

    hey guys just got back fron oreiilys fixin to put my powerhead back on cant find my brp with lid will a light film of wheel beraing grease do for anti sieze im in the middle of it know also powerhead gasket dry is good right thanks bennyb
Top