Search results

  1. W

    Cant figure out what this is.

    Re: Cant figure out what this is. Maybe these images will be right side up.
  2. W

    Cant figure out what this is.

    I cannot figure out what this is. But the thing in the 2nd and 3rd pic is leaking fuel bad. I had it out this past week and when I gave it throttle it didnt go anywhere. It felt like it was starving for gas. It would idle fine but when I put it in gear it wouldnt go for nothing. (for some...
  3. W

    88 Johnson 110 not starting unless open carbs

    Hey all, I have a 88 110hp Johnson that wont start unless I manually open the carbs. Any ideas? I just redid the carbs on it so I know they are clean.
  4. W

    88 Johnson not starting. Starter barely turns flywheel

    The video will explain all. The battery is fully charged. It will turn it over maybe 1/7 times, the rest, it just does like in the video. Also the starter gets very hot after about 5 times trying it. Any ideas?
  5. W

    New ignition switch has different letter than old

    I had to get a new ignition switch for m boat and all the letters are the same but there is an A on the old switch and an I on the new switch...Are they for the same wire? I thought I hooked it up right but the starter was going counter clock wise (backwards) and was not engaging. EDIT...
  6. W

    Is my steering arm supposed to look like this?

    Re: Is my steering arm supposed to look like this? Ok, Another small question. I was watching a video on how to replace the stearing cable and they were using a "iHook" to hoist the motor. I have searched again for one of them "iHooks" that get screwed about the flywheel and cant find one...
  7. W

    Is my steering arm supposed to look like this?

    Re: Is my steering arm supposed to look like this? I got the steering cable off today and I cannot find anywhere to purchase a new one. Can someone tell me what exactly this is called and where I can buy a new one please?
  8. W

    Is my steering arm supposed to look like this?

    Re: Is my steering arm supposed to look like this? Yes the motor turns very easy and stops when it hits. And it was like that when I bought it. I didnt think it looked right when I got it home. Not complaining, I only paid $500 for boat, trailer and 110hp evinrude.
  9. W

    Is my steering arm supposed to look like this?

    Re: Is my steering arm supposed to look like this? Gotcha, well when I took it off, I didnt notice that the part it connected to broke off. Is that a whole new cable I have to get or is it a single rod? Anyway you can tell me what thats called? Heres a pic. You can see the piece that broke.
  10. W

    Is my steering arm supposed to look like this?

    It looks bent to me but I dont see how it could have gotten that way. The motor can turn to the right, but when I try and go left it hits and stops in the middle. Its from a 1988 evinrude 110hp
  11. W

    1988 Evinrude 110hp power trim just clicking

    I just boat a new boat with a 1988 110hp evinrude VRO and when I try to trim it up or down with the buttons on the throttle arm, it is just clicking. Any ideas? It has a fully charged battery on it. Model - E110TLCCA Serial - R1814009
  12. W

    19801 80hp Mercury stalling when giving throttle (except when chokes in). Please Help

    Re: 19801 80hp Mercury stalling when giving throttle (except when chokes in). Please This is what I have when the motor is in idle. The idle stop screw isnt even touching.
  13. W

    19801 80hp Mercury stalling when giving throttle (except when chokes in). Please Help

    Re: 19801 80hp Mercury stalling when giving throttle (except when chokes in). Please I have been turning the screw on the right. Does the screw on the left have a purpose and should I be adjusting that also?
  14. W

    Space between motor and boat where it mounts..

    Re: Space between motor and boat where it mounts.. Its a fiberglass. I dont think the wood is wet. I am not complaining. I only paid $200 for the boat, trailer, motor, and trolling motor. It sat for 2 yrs before I got it. I am hoping a steel plate or a transom plate would fix this little...
  15. W

    Space between motor and boat where it mounts..

    Re: Space between motor and boat where it mounts.. Here are a few images. Its the best I could get of the inside.
  16. W

    Space between motor and boat where it mounts..

    I have about a 1" space between the motor and the back of the boat. (seen in image) What can I do to fix this? Would a steel plate on both sides of the hull work? Is there a special name for that and can I order one? I am not sure if the hull is rotting out.
  17. W

    19801 80hp Mercury stalling when giving throttle (except when chokes in). Please Help

    Re: 19801 80hp Mercury stalling when giving throttle (except when chokes in). Please Once the boat gets up to speed I can let off the choke and it runs fine. Its just getting it up there. I have attached a pic of the carbs from when I took them out. They are clean as they can get.
  18. W

    19801 80hp Mercury stalling when giving throttle (except when chokes in). Please Help

    I just had the carbs redone. Had to take the flywheel off because there was a wire to the trigger plate that needed replacing. Motor ran fine with the muffs on but today I just took it out and it started and idled great, but when I went to throttle, it wouldnt go anywhere unless I held the choke...
  19. W

    1981 80hp Mercury throttle problem

    Re: 1981 80hp Mercury throttle problem Here is a pic of the wires coming from the trigger plate. Does this make sense or am I missing something?
  20. W

    1981 80hp Mercury throttle problem

    Re: 1981 80hp Mercury throttle problem I also noticed when I took a detailed look at the wires going to the coil packs and the switchbox some were crossed. It also looks like I am missing a wire going to the trigger plate, as shown in the images attached.(highlighted yellow)
Top