Search results

  1. A

    Cdi power paks

    Hello all, well i recieved my power pak today which i ordered last week, i orderd a cdi pak for my 98 115 intruder , well i opened it up it was in a evenrude brp box , it looks like a cdi pak which i saw on the cdi web site it is a blue pak with orange wires for the coils one ground wire and...
  2. A

    Omc ht 400

    Hellow, i have a couple of questions , when i get ready to put my timing wheel back on my 98 115 intruder the shop manuel says to prime the bolt it with omc nut lock primer than use omc ht 400 adhesive what is this ,is there a substitute i can use , it also says to use new bolts on the fly wheel...
  3. A

    98 115 intruder with ois missis or skips

    Hello all, well i have been having this issue with my 98 115 intruder with ois ignition for at least a year now, thought i had it solved where i had a ignition coil that when warm was acting not normal the ohm meter would jump all over when you tapped the coil so i replaced it went out to see...
  4. A

    98 115 intruder misses or coughs when reveing up in nutral

    Hello all again, i have a issue with my 98 115 intruder , it runs very well since i rebuilt the carbs comes out of the hole very well hits 6000 rpm wide open no problem , this is what i noticed when i bring up the rpms to about 1400 to 1600 in neutral it will cough or misifire a few times but it...
  5. A

    Engine tuner

    Hellow i have a question about using omc (brp) engine tuner, i know that it needs to be done every so often to clean up the carbon on the pistons and around the rings as to help the motor have good compression but my question is does it also help clean up or free up the recirculation check...
  6. A

    Slow speed issues

    Hellow i have issue with my evenrude 115 intruder it has a skip at very low speed when you go threw a channel at about 1100 if you bump up the throttle just a little toabout 1300 to 1400 the skip goes away , what i am asking one of the techs is at what point does the slow speed mix circut stop...
  7. A

    Slow speed mixture adjustment

    Hellow, i have a question about adjusting the slow speed mixture screws on evenrude outboards, i have read that you realley cant get a good adjustment in a barrel or horse trough or on the muffs you can only get it close , you have to final tune it at the lake , i belive it has somthing to do...
  8. A

    98 intruder sneeses

    Hellow all i have a question about the slow speed needle setting on my 98 intruder, carb rebuild went well no fuel running out of the carbs engine saeems to run fine, today it was nice outside so i decided to dial in the slow speed needles in my large hourse watering trough. I let the moter warm...
  9. A

    Low speed needle adjustments

    Hellow all, well its been almost two months since i have rebuilt the carbs on my 98 evenrude 115 v4, and today it finalley warmed up to 60 degrees so i brought the boat out of the shop to see how well i did with the carb rebuild and link and synk. I preset the low speed needles at five and three...
  10. A

    Gas leaking out of my 98 evenrude 115 intruder carb

    Hellow all, well i finally got my carbs cleaned out , they were very clean inside replaced all gaskets needle and seats and set the float height just slightly off level like everybody says, and torqued bowl screws down to factory specs no problems , put carbs back on motor did link and sync a...
  11. A

    Omc float guage

    Hellow all, i have a question about the omc float guage that i just acquired from a friend that had it laying around that he never used,i tried to check with this guage using the v4 v6 cut out but it is not even close to what the spec one thirty second plus or minus one thirty second i set...
  12. A

    98 115 intruder needle seat

    Hellow every one, as i was doing my carb rebuilding on my 98 115 intruder i noticed that my carb kit came with a needle seat that has a larger hole in it than what the original equipment has is this a upgrade , or vender supplier changes, my concern is will this affect the carburator...
  13. A

    Low speed needle adjustments on a 98 115 intruder

    Hellow all, first i would thank all of you for the information on carb rebuilding from a preveous post, well i have a question my low speed needles are set from the factory at about six and a half turns outwhich i belive is quit a bit, nobody has touched this motor since it was new so i know the...
  14. A

    98 115 intruder carb rebuilding

    Hellow all, im in the process of rebuilding my 98 115 evenrude intruder carbs, what my concerns are the torquing to the screws that hold the bowl on and other self taping screws used on the plastic nylon carbs. When cars were assembled at the factory the threads were cut by the selftapping...
  15. A

    98 115 intruder

    Im going to be in the process of cleaning out and rebuilding my carbs on my 98 evenrude115 intruder v4, what i would like to know is it nessesary to remove the lower cowling to gain access to the lower carbs, the factory manuel doesent realley tell you but the seloc manuel does any help would be...
  16. A

    omc shift rod

    I have a 98 omc 115 intruder that i just replaced the impeller on, what i am having issues with when i dropped down the lower unit my shift shaft that has a angle on it was facing towards the front the manuels say it has to face the rear dont know if it turned when droppig down the lower unit...
View older results
Top