Search results

  1. S

    98 225 Rude System Check Engine Light Came On

    The first time I shut it down and started up again and remained off. Today it came on thirty seconds after start up. Engine died by itself. Hard starting it up again. Finally got it to start and engine light/warning again. I am resigned to replace the fuel lines,filters and priming bulb...
  2. S

    1998 225hp Rude not charging.

    No change in amps when I throttle up. Meter shows drawing 1.4 amps at idle and at 3/4 throttle. Battery showing 12.40 volts running or not. Should I replace rectifier ? stator ?
  3. S

    1998 Evinrude 225HP Fuel Filter

    I currently use a Racor 320R-01 Fuel/Water Separator head w/ S3227 filter and clear bowl. This system has worked well for many years. The painted head is getting corroded and I was wondering can I use a stainless steel head ( Marpac? Sierra? Other?) with a Racor S3227 element and my clear...
  4. S

    Trim/Tilt leakdown 2009 90hp Etec

    After I tilt the motor up after use ( boat is left in water) when I come back in several days the motor leaks down to it's operating position. This is a nuisance since the brackish water stains the lower unit badly. Is there a simple fix for this? Thanks
  5. S

    Remote oil fill cap , vented ?

    Trying to install a deck mounted remote oil fill for my VRO oil tank. Must the cap be vented? If yes is there a stainless deck fill that is suitable other than the plastic/ zamak found in the OMC kits. OR Is there another way to vent the tank allowing me to use a solid stainless non-vented...
  6. S

    Check Engine Light at WOT

    I just splashed for the season ( yeah I know it's late...but I do have another boat).... I bring my 225 1998 evinrude up on plane and 1-2 minutes at WOT and the light and audible alarm come on. Back off on the throttle and the alarm goes away. I did install a Sting Ray hydrofoil this season...
  7. S

    Scrader Valve indicator ?

    I can't remember the proper setting for the red arrow on the scrader valve for normal running? Thanks 1998 225 rude
  8. S

    Remote Oil Fill Question

    Does the oil cap need to be vented? I see that I can purchase a OMC remote oil fill kit but I would prefer a stainless fill and cap but I am assuming the OMC kit uses a vented cap? Anyone know for sure what I need? Thanks
  9. S

    What Gearcase Lube?

    1998 Ocean Pro 225hp...Manual calls for OMC ultra gearcase lube. Marina says BRP HPF will work. I also have some BRP Hi Viscosity left over from an older Rude I had. What will work for my application? Thanks
  10. S

    Mercury Force History

    Guys.... trying to clear up some misconceptions (maybe mine) regarding how much design change did Mercury influence Force when they took over until the phased them out. I always believed while Mercury made some changes including lower units, ignition etc. that the powerheads were indeed Force...
  11. S

    Wrong Water Pressure Gauge??

    I installed a water pressure gauge 0-30 psi on my 1998 225hp Rude. At wide open throttle the gauge pins. At idle I am seeing 15psi. Should I have gotten a 60psi gauge?
  12. S

    What Did I do to my E-tec????

    2009 E-tec 90hp. I went to the boat to mount a few gauges (water pressure and trim) Mind you I was not hooking them up yet...just wanted to mount the gauges to the panel. I took of the cowling to search where I would tap the WP gauge and found the plug ..closed the cowling did not touch...
  13. S

    Water Pressure Gauge Hook Up 98 225 Rude

    Try as I may...I can not find an obvious place to tap the 1/8" NPT fitting off my 1998 225 Rude. Any help?
  14. S

    Tilt Trim Compatibility

    I have a 1998 Rude 225 tilt/trim system that leaks. I also have a 1991 200 Rude parts motor. Can I use the T/T system from the older motor for the 98? If not is re-sealing the system a big deal?
  15. S

    Rebuilding Tilt/Trim 1998 225 Rude

    How difficult a project is this? Is it just a matter of replacing some gaskets and seals and possibly a motor or does this require specialized tools and wherewithall and better left for the pro?
  16. S

    Converting from Sure-Lube to Bearing Buddy

    I have Sure-Lube bearing caps on my Tidewater. Is it possible to convert to Bearing Buddies? Is this possible or unwise?
  17. S

    Electric Winch Choices

    I'm getting to old to hand crank my 4000lbs. + boat. Any preferences out there for Powerwinch vs Dutton-Lainson or others? Your opinions, experience and recommendations will be greatly appreciated.
  18. S

    Increasing Trailer Weight Capacity

    Is it possible to boost a trailers capacity (e.g. 10%) by swapping the springs of each axle?
  19. S

    What is a 1992 85HP Rude?

    Looking for a replacement for my 90HP Johnson on my Boston Whaler Montauk. I came across a guy with a 1992 85HP Evinrude. I never heard of them only being familiar with 90hp and 88spl. Can anyone give me insight on this particular motor. It has VRO and TT. Thanks Michael
  20. S

    V6 Tilt and Trim Compatibility

    I have a 1991 200hp Evinrude parts motor. Will the Tilt/Trim assembly from this motor fit my 1998 Evinrude 225hp?
Top