remote motor control on-off-start

[ttles714]

I am looking to start, run and stop my 2007 F250 from behind the engine when it is on the trailer, I want to avoid having to go to the helm when i am servicing . Is there a "tool" for this ??? I can't seem to find a wiring schematic if I have to make one .... Any help or information welcome ....thanks

 

[boscoe99]

Wiring diagram is in the back of the applicable service manual.

No tool available. You will have to devise a means on your own.

Most practical and cost effective way would be to disconnect the ten pin connector at the front of the motor. On the motor side connector jumper the red wire terminal to the yellow wire terminal. That will turn the ignition on.

To crank and start the motor momentarily jumper the red wire terminal to the brown wire terminal. That will engage the starter motor.

To stop the motor jumper the black wire terminal to the white wire terminal.

Or you can buy a used Yamaha 703 control box or an aftermarket 703 control box in which case you will disconnect the ten pin coupler on the motor and connect the ten pin connector from the 703 control box.

 

[ttles714]

good information , pretty much what I was looking for .. I think what i am going to do is find a 10 pin harness to plug into the motor's ten pin connector ... Then modify that harness with a couple of switches .. If you have the time, could you take a look at the link below and let me know if this would work out for a starting point for this project .....thanks very much much

 

[Chris1956]

They have remote starter cables for Mercs and other motors. Mechanics use them on motors mounted on stands. You might look for them.

The other choice is to make one. Find a short engine cable extension and a keyswitch and wire it up.

 

[boscoe99]

They have remote starter cables for Mercs and other motors. Mechanics use them on motors mounted on stands. You might look for them.

The other choice is to make one. Find a short engine cable extension and a keyswitch and wire it up.

What Yamaha calls a boat in a box. Box being used to segregate the motor from the boat when trouble shooting.

 

[boscoe99]

https://www.ebay.com/itm/147304927029?_trkparms=itmf%3D1%26aid%3D1110006%26rkt%3D12%26asc%3D341166%26pid%3D101875%26mech%3D1%26algv%3DSimplAMLv11WebTrimmedV3MskuWithLambda85KnnRecallV1V2V4ItemNrtInQueryAndCassiniVisualRankerAndBertRecallWithVMEV3CPCAutoWithCassiniEmbRecall%26pmt%3D1%26amclksrc%3DITM%26sd%3D397921569466%26sid%3DAQALAAAAEOZD1OQYPWW%2B1y8MbYWtAPo%3D%26itm%3D147304927029%26noa%3D0%26plcampt%3D0%3A162996508018%26algo%3DHOMESPLICE.SIM%26ao%3D1%26rk%3D6%26mehot%3Dnone%26lsid%3D100%26meid%3D8222d43d5be74704bd90b2db7b46f270%26pg%3D2332490&_trksid=p2332490.c101875.m1851&itmprp=cksum%3A1473049270298222d43d5be74704bd90b2db7b46f270%7Cenc%3AAQALAAABcOrUAJyocs9zq5pLBX3YtmatWsILip3iH8cXvCuqAHQycQTv%252F0%252FsvMD%252FiujDLuk04YfjG4hB1bvoSoZT22fSr86l4ZShqsEbKB92VPEA3U8iJy4PIJKdxno0JaAN1O0l9SNW8FeXf9POlGhR7no0dngpp41JhUposDyp8wrIWePZ2WVit%252Fs77Ssad66Av4xRotWqSwXzmlEHRAcdtnHw38QO2B0t45AnVxfTerZlE9t2SxF%252FO2glVSphbhwxcItRbkP4KXbilTAXKFzwntDsevlYVAIPsio0GJmIRfgazhJjez3BJ83SxrMJh%252F8AP3c7DwC5UYE4m%252FUZsKJnR2%252BI05WaPUzFDQKdaV9k4WAo0BJbIBlIP9D1ARKFYs59itAkpFYqZzLK9GFFLd5dzGZb%252FX8HUdtQw4u1yq4l3Tpayjs3kN7FNELXnZFWKWWXR3nfeTxgZiiLsdxlANTWgUiAHCmcmidA7a4n8HOfbZJjw6eM%7Campid%3APL_CLK%7Cclp%3A2332490&itmmeta=01M0TVGPW0FB2K62ESDEAD63Q9

 

[ttles714]

Boscoe 99 ... thanks buddy ... Based on what you told me ... here is what i am going to put together .. I am going to mount the switches in a small project box.. I have a momentary switch with a cover that has to be lifted to activate. This adds a little more safety to avoid accidental activation.... Thanks for the link to the extension cable and for letting me "pick your brain" Much Appreciated !! tony

 

[ttles714]

Ok >>> so I finally got around to putting this together ... Pretty simple and straight forward .. NOT !!! I picked up an old used harness FROM a 703 control box .. I kept about 6 feet OR WIRE from the female connector and hooked up all the wiring and switches .... Tried it out and nothing !!! Long story Short >>> In the harness female connector, the 12V+ and 12v- were in reverse positions.. Opposite that of my motor and any diagram I had ... I wound up using the black as positive and the red as negative . I don't really understand why this occurred ????? All other wires were in the proper position...Did Yamaha change harness part #'s ??? ANY ONE HAVE AN ANSWER ???

 

[ttles714]

picture of harness and control .. still can't figure out why this harness had the 12v neg and pos in opposite positions from the engine and any schematic I looked at ... The connector is intact and was not modified ..... So To be clear ,,, the positive pin on the motor lines up with the negative pin on the control harness and the negative pin on the motor lines up with the positive motor pin !!

 

[boscoe99]

Something is not adding up.

 

[99yam40]

it might help if the OP would post proof of what he is seeing