Current visitors

Home
Members

Bondo's latest activity

Bondo reacted to DeepCMark58A's post in the thread Can I add a bushing? with Like.

So got the new starter in and did a wet test, yes it works as good as the $60 one I found online.

Jul 4, 2026
Bondo replied to the thread persistant overheating issue..

Ayuh,..... Which one are we talking about,..??

Jul 4, 2026
Bondo replied to the thread Popping noise when lowering outdrive.

Ayuh,...... 'bout the only other thing that could make that noise could be very dry dragging hinge pins,.....

Jul 4, 2026
Bondo reacted to Bt Doctur's post in the thread Popping noise when lowering outdrive with Like.

loosen the nut and raise and lower the drive again If no more noise remove and lubricate the bushing and retighten If it still make a...

Jul 4, 2026
Bondo reacted to BeelLPHondaBF225A's post in the thread Engine cranks up but dies when I release the key to the run position with Like.

After a few hours of checking voltages and changing filters I jumped the kill switch. That was it!! Thanks for your post!

Jul 4, 2026
Bondo reacted to cameron92's post in the thread Help! Bought a 1993 Four Winns W/ 5.0 OMC Cobra Motor and Drive - Losing power after crusing with Like.

So found the issue it's been having all along. The anti siphon valve was clogged up with white deposits. Cleaned it out and now the boat...

Jul 1, 2026
Bondo reacted to JFCMoore's post in the thread Cannot get outdrive installed to the last 1/2 inch - need your advice! with Like.

I finally got it. I don't know if it was the oil on the o-rings, leaving the alignment tool inserted while I turned over the engine (to...

Jul 1, 2026
Bondo reacted to crazy charlie's post in the thread How to run twin 5.0s from portable outboard tanks with Like.

UPDATE. ,launched yesterday with 3 gal outboard tank with 2 prong connector. All fine with both motors running at idle speed.Went up...

Jul 1, 2026
Bondo reacted to Boilers2000's post in the thread Fluctating Voltage with Like.

Thanks again for everyone's input and advice! The knowledge base in these forums is amazingly extensive and helpful!

Jul 1, 2026
Bondo reacted to ShoalSurvivor's post in the thread fuel sender install w/sealant or dry with Like.

FIXED!! Turns out that the replacement bolts were just a hair too long for my threaded inserts. I was able to snug them all down and it...

Jun 30, 2026
Bondo reacted to dingbat's post in the thread fuel sender install w/sealant or dry with Like.

Gasket (cork?) should be installed dry. Run a tap through the messed up hole to clean up the threads. Install bolt with fuel resistant...

Jun 30, 2026
Bondo reacted to alldodge's post in the thread 1984 3.0 cobra with Like.

The great part about the 3.0 is it has a inspection cover, so if there is a bad lifter it can be replaced without tearing the motor down

Jun 29, 2026
Bondo reacted to kenny nunez's post in the thread 1984 3.0 cobra with Like.

What is wrong with the lifters? If they are cupped on the bottom you will need a new camshaft also.

Jun 29, 2026
Bondo reacted to ShoalSurvivor's post in the thread Found bolt in 4.3 bilge. Please help identify with Like.

Good news - all three coupler bolts are still in. Better news! Found it! It was the 3rd bolt holding the power steering pump to the...

Jun 27, 2026
Bondo reacted to ShoalSurvivor's post in the thread 4.3 crankshaft/housing oil leak - next steps? with Like.

Just reporting back - didn't wanna jump the gun. I pulled the engine, replaced both front and rear crankshaft seals, removed and...

Jun 26, 2026

Show older items

Home
Members

Top