Search results

  1. B

    What slide hammer to get?

    The bearing case is stuck in a 30hp Evinrude and I have read where Omc makes a slide hammer for this purpose. One person used a slide hammer with an adapter and nut that would keep it on the end of the prop shaft. I might need it for an 8,9.9, 35, and 50 hp Evin/Johnson's. Some don't have j...
  2. B

    30hp bearing carrier

    The seals were finally removed but the carrier has a small crack which goes about 1/2 way to the bottom and the back looks out of round to me. There are two light scratches on the prop shaft about where the top of the second seal was. One is 1/4" long. This carrier is in a1986 Evinrude and has...
  3. B

    How did Glastron expect to put a kicker motor on this one?

    As you can see the back slopes down and back in. A standard kicker attachment won't work. Thanks.
  4. B

    I need to re-thread carb bolt stud

    One bolt stud that holds the carb on a 1985 Evinrude E8RCOB motor got the threads rounded off on the end. What size should I recut the 1/4"end piece too? Will it hold ok? I took the intake manifold off to make it easier to work on. It would cost $25-50 to have the bolt replaced. Thanks.
  5. B

    Is 85w-140 gear lube ok up to 50hp?

    Got it by mistake since I usually use 80-90w in the lower unit. Thanks.
  6. B

    48 only starts at full throttle

    This '96 48 Johnson will only start at or near full throttle. It idles roughly and dies if the throttle is brought back towards neutral. The fuel pump diaphragm is stiff but it started normally before I took it apart and the carbs were cleaned. Is it the fuel pump and why? It has 2 ports and the...
  7. B

    48 Johnson fuel pump/3 port/ lines

    This '96 motor's fuel pump won't let the fuel go through while pumping the bulb. Doesn't the manifold line go to the outside edge and the fuel to carb line go to the inside port? Thank you.
  8. B

    1996 48 tilt release broke_How to gt it up?

    This motor is a 1996 J48ESLEDC. I see there is a short rod that the tilt release lever should be hooked to, but I don't know how it locks. There are two small holes on the side of the bracket about where I think this short rod ends. I've been trying to knock the big pin out at the bottom of the...
  9. B

    electolasis show through cold tar epoxy

    I was wondering how effective cold tar epoxy is on aluminum. After applying, a month or so later that white powder look of electolasis starting showing up. Thanks.
  10. B

    Sea King 3hp steering froze and float lock question

    The model is 15GG-9004. We found this motor at a garage sale and bought it for $10. After freeing everything else up we still can't get it to turn with the handle. Using PB Blaster and heat didn't work. From the looks of a diagram, th thrust washer and/or exhaust seal might be froze up. The...
  11. B

    Bad crankshaft seal or seals on 9.9?

    I am having the same problem with this '92 Johnson J10RENA as before. It won't get a 14' aluminum boat up on plane like it used to. How can I tell if the CS seals are bad? This motor got used about 3x in10 years and it probably sat in the Florida sun the rest of the time. I put 10-15 hours on...
  12. B

    Substitute carburetor for '92 9.9 ? warped

    As some of you already know I've been having trouble with this '92 Johnson 9.9 J10Rena for about two years. First it was the fuel pump. That got the power back but it wouldn't start using the choke. So I took it apart for the 15th time and reamed the holes with wire. Again idle only. That might...
  13. B

    Should choke plate open all the way with spring or vacuum?

    Hi I'm still having trouble getting this 9.9hp started so I cleaned the carb again. I noticed with the choke buttom all the way in, the choke plate wasn't open all the way. The springs on the side lever don't seem to do anything. Is it wupposed to work this way? Will the vacuum open it or...
  14. B

    9.9 won't start with manual choke

    Still have one big problem with this '92 9.9, it will only start with a shot of mix. I covered the hole on the choke plate thinking it might get a richer mix but it didn't work. It worked before the fuel pump went bad. The choke plate is fully closed. The motor runs fine otherwise.
  15. B

    Manual starter spring for 9.9-sub lawn mower part?

    Hi, I need a spring for a manual pull start, the one with the bolt through the top. The sierra part is 18-6434 and costs about $20. Are there any substitutes that will work cheaper? Seems to me like $5 or so is more like it. Thanks.
  16. B

    What pulley puller for bearing case 30hp

    I have a 1986 Evinrude 30 horse motor. Lately I have been getting more and more JB blaster to go behind the bearing case using heat. The 1/4" threaded bolt broke today. Is there a pulley puller that will catch the inside rim of the bearing case to get more bite and pulling strength? Thanks.
  17. B

    '92 9.9 carb hole exit?

    In the bottom just in front of the throttle plate there is a tiny hole. I can't tell where it comes out at by shooting carb cleaner in it, so I don't know if it is blocked. I wanted to ask before putting it back together again. This motor has a power problem and I don't want to miss a thing...
  18. B

    9.9 carburetor choke springs position

    The springs on this '92 Johnson have no affect at all. Ther is one loose end and it doesn't seem to go anywhere. Maybe the picture will help. Thanks.
  19. B

    Any Any difference in '91 and '92 9.9 OEM manuals?

    Someone on Ebay sold me what was advertised to be a 1992 Johnson manual and it was actually a 1991. I am going to let him know that advertising like that is fraud, even if the manuals are informationally the same. Thanks.
  20. B

    9.9 synchronization and linkage question

    Never mind, I think I got it figured out, I hope
Top