Search results

  1. B

    What are threads for in gearcase/prop area? '86 Ev

    Is there a ring screwed in and welded to keep the bearing carrier from turning? It looks like the tab at the top might fit into a notch in a ring.
  2. B

    Trouble removing prop seals on 30hp

    Hi, My '86 Evinrude prop seals are leaking. A flywheel puller, heat, and PB blaster won't budge the bearing carrier. Ezeke mentioned a Lisle shaft on seal puller. How does it work? And how do you get the seals back in evenly on all sides with the prop shaft preventing a socket from tapped on...
  3. B

    Evinrude 30hp 1986 oil retainers

    Evinrude 30hp 1986 E30ELCDM E0628114 I need to replace these oil seals in the bearing housing. My OEM for a '79 looks similar but doesn't say if the two bolts in the bottom of the bearing housing come out. I would guess yes. Is that correct? Do the screw seals need replaced too? Thanks.
  4. B

    E30ELCDM '86 30hp fuel pump lines and primer solenoid lines

    My Dad just got a 30hp E30ELCDM motor. I need to know where the fuel lines go from the fuel pump (one goes to the bottom of the carburetor of course) and where the 3 lines go from the primer solenoid. I'm thinking that the big port on the PS goes to the barb on top of the carb. Thanks. Bob
  5. B

    Anyone know what this oil is from?(picture)

    It is a 1992 9.9hp Johnson motor. The oil is also coming out of the vents where the water comes out just above the lower unit. Thanks.
  6. B

    Evinrude superfast twin 7hp gearcase

    This motor has the two line fuel system. The gear case was full of water and the bearing or seal on the back on prop shaft is beat up. Do I turn it upside down and take the bottom cap off? Will anything fly out? How does that seal/bearing go in? Will a 1/2" socket go over the prop shaft or...
  7. B

    What about this smaller lower unit on '62 40hp?

    We were wondering how it would effect performance. It sure looks strange.
  8. B

    Johnson RDSL-24M year, and lower unit

    It is an electric Sea Horse and I think it is a 40hp. What year would it be? The lower unit looks too small. Is it possible to put a smaller one on and work? Who has parts? I Evinrude/Johnson only goes back to 1968. Thanks.
  9. B

    Do magnatune's go bad?

    I have a 7 1/2hp Evinrude SN#15012-44241 with no spark. It has magntune modules. Do they go bad? Sierra has them. Thanks.
  10. B

    '57 Johnson 35hp fuel conversion finished

    Thanks to Tashadaddy, TM Calavy and many others who posted pictures and answered my questions, I got it running this morning. Here are some pictures. I don't have a licensed boat for this motor so a real tuneup and test will have to wait. I decided on the Mikuni fuel pump from Spruce...
  11. B

    Johnson 57 35hp carb

    I have a picture of a 56 carburetor but it isn't a very good picture. Does the sharp fuel needle go in the top or bottom? Neither the sharp nor round needles will grab the threads in the back. I assume the brass tubes they go through go out the same distance from the face of the carb after...
  12. B

    Will JB Weld work on bypass cover and pressure barb?

    Well the drill and tap job left a little slop in the barb fitting for a fuel conversion. Will JB stand the heat? Thanks.
  13. B

    What drill and tap size for 1/4x 1/8" barb fitting

    It is being used for a vacuum port on a '57 Johnson. It is a Watts #17090192. Thanks.
  14. B

    '85 8hp Evinrude carburetor attachment bolts replaceable?

    It is a model E8RCOB and the threads are bad on one of the bolts that hold the carb on. Are they replaceable through the back? Thanks.
  15. B

    Will 8" wheels last for 1400 miles?

    I have one similiar to Northern Tools boat trailer. It has a 14' wide and deep open aluminum or steel hulled boat on it. We might put a 46" riding mower or other stuff in it too. Are the bearings and wheels good enough to go 1400 miles in 3 days? Thanks.
  16. B

    3 different forums and no solution for 9.9hp lack of power

    1992 Johnson 9.9 J10RENA idles great but won't get up on plane. It has a new carb kit, redesigned carb cover, fuel pump kit, spark plugs, fuel lines. and a fuel filter between the fuel pump and carb. The carb has been cleaned about 10X. The high speed jet was clean when I took it apart the...
  17. B

    How do I re-sync the motor on '92 9.9hp?

    It's a J10Rena Johnson motor. Thanks.
  18. B

    How can a switchbox go bad just sitting there?

    Take a 50 hp 2 stroke 3 cyl. Mariner for example I think they call the box with all the wires going to it a switchbox. We put this motor on that back porch and after 3 years it lost the spark. What would cause it to go back under these circumstances?
  19. B

    Johnson 9.9 gags, timing question too

    This motor is a '92 J10Rena with a manual starter. I put a new carb cover kit on it along with a carb kit. It idles ok but it won't get any kind of power unless you run it a full throttle for a bit and back off 1/4" then it moves right along although I'm not sure that the best it will do. If...
  20. B

    How does '92 9.9hp starter install?

    It's been over a year since I took this thing off and the library manuals don't show a picture. I tried leaving the red cam lever on the outside of the vertical starter bar but the speed control wouldn't move. Does the red bar go inside the vertical bar on the outside edge of the starter? And...
Top