Search results

  1. Bondo

    MerCruiser 4.3 1990 Rinker Alpha-1 Gen-1

    Ayuh,.... At an inch, 'n 1/4", ya need to turn the motor, or the drive to align the splines into engagement,....
  2. Bondo

    Mercruiser 3.0 1988

    Ayuh,...... Welcome Aboard,...... Is the drive on it,..?? If so, is the drive down,..?? Idle should be 650/ 700 rpms,.... If the drive is on the boat, 'n tilted up, my guess is yer shredding the u-joints,....
  3. Bondo

    Bravo U joint Bellows Do Over?

    Ayuh,...... Spray the bellows, where it contacts, 'n get hung-up, with QuickSilver Power Tune,.... It'll slip right on,.......
  4. Bondo

    closed cooling

    Ayuh,..... It'll have to be a Huge H/E for a full system,.....
  5. Bondo

    Chasing Down Fuel Delivery Issue

    Ayuh,...... Carbed, or Efi,..??..?? Fuel pressure,..??
  6. Bondo

    81 omc sterndrive

    Ayuh,.... What's the back-story on this project boat of yer's,..?? Has it ever worked right since you've had it,..?? I don't believe that ole Stringer drive will hold up to running in reverse for very long,.... Maybe Southkogs can shed some light on this,....
  7. Bondo

    Bravo Installation Kit ( ring gaskets)

    Ayuh,..... No worries, the o-rings just snug against the shaft, inside the gimble bearing,...
  8. Bondo

    Bravo Installation Kit ( ring gaskets)

    Ayuh,...... I use grease too,...... Maybe abit of perfect seal, if the funky o-ring/ gasket thingy wanted to fight,....
  9. Bondo

    350 Mag Bravo 3 with poor power steering assist

    Ayuh,...... So, when you changed the cable,.... What condition, 'n which helm are you dealing with,..??
  10. Bondo

    4.3 crankshaft/housing oil leak - next steps?

    Nope,......
  11. Bondo

    Engine Swap

    Ayuh,........ Is the 350 carbed,..?? The Efi from the 5.0 won't run right on the 350,....
  12. Bondo

    Stripped threads on carburetor

    Ayuh,....... I see 2 options,..... The Best, would be to find a used carb body casting that ain't stripped out,.... I don't see taper, nor a compression fitting,... I believe, originally, there was a sealing washer 'tween the brass, 'n aluminum casting to seal it,..... The line, 'n...
  13. Bondo

    Should new gimble bearging gimbal? allow shaft to roll, pitch and yaw?

    Ayuh,...... It's supposed to move pretty hard,...... That factor allows us to align the drive to motor, 'n it to stay where you put it,... Cool video, by none other than my friend, 'n former Mod. here at iboats,.... Achris,.............:)
  14. Bondo

    Good spray on weed killers.

    Ayuh,..... Clorox Bleach,....... It kills everything it hits, 'n dissipates in no time,.... Used it for years to kill dandelions, 'n bamboo, that'll grow right through 2" of fresh blacktop in a couple of weeks,..... Dump abit of Clorox into the hole it forms, 'n beat the bump back down...
  15. Bondo

    350 Magnum Tournament Ski spark plugs

    Ayuh,...... Yer symptoms, 'n that plug says it's detonating, probably from a lean condition, or possibly to much timing,....
  16. Bondo

    Bravo 3 turns hard starboard underway

    Start a new thread of yer own, this one is an antique,....
  17. Bondo

    Volvo Penta 5.0 GL PWTR - severe overheat - thought I was on fire - troubleshooting Questions

    Ayuh,.... Nothing "Marine" 'bout 'em,.... Same as heads used on pickup motors, which are the same as standard production automotive motors,....
  18. Bondo

    best way to repair gimbal hing pin threads?

    Ayuh,...... Maybe, never tried it,..... To be sure, find a used freshwater used helmet,....
  19. Bondo

    need help identifying this steering actuator

    Ayuh,....... Welcome Aboard,...... My guess is, it's for a '99 Volvo SX drive,..... P/S actuators are pretty much all the same,.... hose attachments might vary abit,.....
  20. Bondo

    Outboard won’t trim down enough

    Ayuh,....... Goin' from a prop to a jet, you might need to cut down the transom to make it work,...... With the clutter in the picture, it's hard to tell,....
Top