Search results

  1. dingbat

    Unusual Bilge pump power issue

    Black wire disease is real Typically occurs in the first 4-6" of wire back from a connection. Could be ground, but positive side is more common. You'll need an ammeter unless you measure the voltage with the pump running
  2. dingbat

    Seeing 360 Flasher on Fishfinder

    How deep? Helix model and transducer type?
  3. dingbat

    '02 Merc 4 Stroke - Diagnosing bad ECU?

    two cylinders out points to stator Starts on page 112 https://www.cdielectronics.com/wp-content/uploads/2016/12/7th-Edition-Troubleshooting-Guide_RS.pdf
  4. dingbat

    Good spray on weed killers.

    Which one is that? Found all four noted on the label registered with EPA
  5. dingbat

    Good spray on weed killers.

    New Zealand
  6. dingbat

    Time to replace tires?

    Background: Tires degrade over time regardless of whether they are in service. – Tire failures can result from thermo-oxidative degradation (“Tire Aging”) caused by: • Time • Ambient and operating temperature • Partial pressure of O2 in a tire • Flex fatigue • Construction and compounding...
  7. dingbat

    Yamaha 150 Rigging Tube

    Goggle Yamaha rigging grommet
  8. dingbat

    Teleflex sterring

    I suspect the part number for your old part is actually SSC7212.
  9. dingbat

    Spring replacement?

    What’s your issue? Have torsion on a boat and two horse trailers. Oldest will be 25 yro in August
  10. dingbat

    Spring replacement?

    https://www.easternmarine.com/double-eye-trailer-leaf-spring-una-188
  11. dingbat

    Installed trim tabs and fish finder transom mount.... how do I know if it's leaking?

    Now that would make me worry…….5200 is high viscosity adhesive. Not designed to be used as a thread sealer. The installation instructions for my trim tabs specifically said to use marine epoxy.
  12. dingbat

    200 HP Evinrude/Johnson Carb Kit and Rebuild

    Hey, it’s worth a try. Got nothing to loose
  13. dingbat

    What trailer length

    Post #30 is from someone who works/worked for a trailer manufacturer at one time or another It's interesting in the first page of the NATM manual mention above contradicts his statement on the governing body. "This information document or Guidelines merely highlights the major requirements...
  14. dingbat

    200 HP Evinrude/Johnson Carb Kit and Rebuild

    No hoses 4 bolts on top throttle bodies. 2 bolts on lower throttle bodies Just googled the part number 0332319. Turned up 3 pages of results See post #16 I counted the number of turns each screw was out on disassembly. Shop manual give you a “base” number of turns. It started and ran no...
  15. dingbat

    What trailer length

    Never heard of such a thing. Is that a State Law? Mine has to be pushing 6’
  16. dingbat

    Hard start but runs great once started

    Sounds like it's running on one cylinder
  17. dingbat

    Transom Hardware sealing issue

    I used Marine Tex on all my hull intrusions Not sure why you used a "lag bolt". Much more contact area (strength) using wood or sheet metal screws. If I remember correctly, the ladder of my old boat was installed with #14 screws. 316 stainless "screws" are readily available Use recommended...
  18. dingbat

    E bikes

    Volts x Amps = Watts 120V x 10A = 1200 W 1 HP = 745.7 W 350W @ 36V = 9.7A 750W @ 36V = 20.8A Battery 36V x 13A
  19. dingbat

    Transom Hardware sealing issue

    Most grades of stainless steel, 316 is the exception, "rusts" when deprived of oxygen. Given the situation, wouldn't be surprised at all the 5200 hasn't trapped moisture between the bracket and hull. 5200 has a nasty habit of drying out and shrinking, causing leakage and entrapment of...
  20. dingbat

    E bikes

    Starting /in rush current of an DC motor is 5-7 times more than run current.
Top