Search results

  1. K

    Tachometer bouncing

    Be sure the bracket and bolts that secures the starter brush end is tight against the engine block.
  2. K

    Mercruiser 3.0 Trouble Starting

    If you think there is water in the carburetor you will have to at least remove it, flip it over in a clean bucket to check. If there is none then re mount it. Otherwise it needs to be taken apart and cleaned. You may not need new gaskets if you are lucky. Or just get a kit from Sierra. #...
  3. K

    Volvo Penta Ford help

    A then there were thr Holman Moody conversions. I had the good fortune to talk to Ray Moody years ago at his shop in Charlotte, NC. He told me it was a crazy time and they were shipping the Ford/Volvo packages as fast as they could get them out of their Florida shop. Ford was cutting them...
  4. K

    Is this raw water pump serviceable?

    Save yourself a headache and get a new pump.
  5. K

    My 72' gimbal ring has considerable up and down movement.

    The gap in the top should not cause the engine shaking you are describing. A good chance the rear motor mounts are the problem, what happens is the inner steel core has separated from the rubber. Is the engine running smoothly? The easiest way to tighten the vertical clearance is to first...
  6. K

    Impeller spun?!?!?!?

    With the boat in the water start the engine, then remove the incoming water hose from the thermostat housing. Try to stop the water flow with your hand. If it stops easily then the problem is in the drive, one of the grommets that seal the water pipe are leaking. Also if the pressure is more...
  7. K

    Rescued 69 Evinrude Rogue with stringer need beginner tips

    Since the engine still runs and if you give up on the boat that Buick “nail head” is still popular with some old school street rodders. Obviously it is a fresh water only engine. Worth some $.
  8. K

    Mercruiser shifting problem

    With the engine running try pushing the lever that makes the switch cause the engine to stumble.
  9. K

    Rescued 69 Evinrude Rogue with stringer need beginner tips

    The 2 plastic plugs that connects the engine to the main harness is usually where the bad connections exist. The smaller one is for the tilt. Just wait to see how much fun you will have removing the tilt motor, you will invent a whole new vocabulary of “X” rated words!
  10. K

    Bogging down

    Where the fuel line connects to the fitting on the tank is where the suction tube is located. Un screw the fitting from the tank, the tube usually screws into the fitting. If there is a filter in the tube push it out and pitch it. Using teflon tape put it back together.
  11. K

    Oil pressure dropping

    What could be happening is a vortex forms under the pickup screen. Then the oil gets air bubbles. There may be too much clearance between the pickup and the bottom of the pan.
  12. K

    Need Prestolite cap/rotor info

    Post a picture of your cap, rotor the distributor body and the points. Someone on the site will know what you need.
  13. K

    Bogging down

    Get A 6 gallon outboard tank and set it up where it is easy to connect to your engine. Run the boat on the regular tank until the problem starts then switch to the other tank. A very good chance the problem is in the tank suction tube internal filter.
  14. K

    Rescued 69 Evinrude Rogue with stringer need beginner tips

    Yea, if the engine is a V8 then it is a 200. I thought it was a V6. After the Buick V8s then they converted to Chevy 283s then 307s.
  15. K

    Rescued 69 Evinrude Rogue with stringer need beginner tips

    With the ignition on and engine not running shift to forward, try to rotate the propeller, it should lock in one direction. Next loosen the oil drain screws and see what comes out. If the lift still works that would be a miracle. If the carburetor is a 2 barrel then it is a 155 hp, a 1 barrel 150.
  16. K

    No compression with rocker arms torqued

    Most times the sender is the problem. There is a membrane inside that leaks internally, they sometime read normal on start up but after a short time they equalize internally and rear 0.
  17. K

    Rescued 69 Evinrude Rogue with stringer need beginner tips

    Those Evinrude/Johnson boats were very well built and quality was good. Unfortunately they were expensive and priced themselves where OMC most likely lost $. If your boat is a pre 68 model original drive parts are impossible to find. While the engine may still be in good condition that is where...
  18. K

    Remote sticks when going into reverse, but only when in water.

    With the engine off shift into reverse full throttle, the roller should still be in the center of the “V”. If not then look for the ACHRIS tutorial video on this site which should help you.
  19. K

    Volvo Penta Ford help

    Post some picture. That will be some help to figure what you have.
  20. K

    Remote sticks when going into reverse, but only when in water.

    Did you disconnect the shift interrupter switch wire?
Top