Search results

  1. K

    1978 Doral 255B. Penta V8

    There is also a drain hole at the very bottom of the drive, try to plug it when using the muffs to run the engine. This way there will be an ample amount of water to the pump.
  2. K

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    That rust leak is from the pieces of the exhaust manifold that have collected in the front of the drive. You can try digging out the pieces. That area is open to the exhaust and the drain hole is to completely remove any standing water when the drive is tilted. Being careful with a drill...
  3. K

    Nola Mike is in Fl

    No matter where you go, you are still a NOLA yat!
  4. K

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    If you do change to a 351 the distributors do not interchange. Also while the repairs are being made have every pulley that you can remove sand blasted and powder coated. Or at least try to remove the rust where the belts ride and paint them with some epoxy paint. Rusty pulleys eat up...
  5. K

    carburetor suspect problems

    In addition to the carburetor suggestions. Something else to consider, if your distributor is a breaker point style check that the centrifugal advance is not sticking. Also check that the +or bat side of the coil is getting a full 12 volts in cranking mode.
  6. K

    Water in Oil (Again) Head Scratcher

    It appears that one of manifolds or a riser is the source of the water. The reason that water is on both sides is the exhaust passage under the intake will cause water to be on both sides. Blow out the water by spinning it over then spray oil in each spark plug hole. I do not think the engine...
  7. K

    I may need to shim the upper sterndrive questions.

    The lower bearing cup shim is what sets the lower gear. Upper shim just sets the preload which is around 6-8 in“ lbs of rolling torque. If the recess in the cover is still good and the upper bearing cup fits snug then you just need to install the upper shims until the preload is set. Then...
  8. K

    Mercury Scorpion 350 Will not start

    Is your boat a stern drive or straight inboard?
  9. K

    Need Ideas/Advice/Removal of Broken Upper Vertical Shaft Bearing.

    I also have a Harbor Freight 20 ton press and it is quite handy as I still like to keep my hands dirty. When I had my shop I had a 80 ton press and this much I can pass on. If the parts have friction welded themselves together it takes a cutting torch or a right angle grinder to separate the parts.
  10. K

    Carburetor question

    You are probably right about the carburetor being re cycled and it has the wrong parts in it. Maybe someone on the site has a extra correct one to sell that is rebuildable.
  11. K

    Need Ideas/Advice/Removal of Broken Upper Vertical Shaft Bearing.

    Go to Home Depot or Harbor freight obtain a 4“ or a 4.5” right angle grinder with the abrasive wheels. Start cutting across the bearing, eventually you will be able to peel it off even if it was friction welded. Depending on how bad the shaft surface is you should be able to dress it enough to...
  12. K

    Carburetor question

    Is the carburetor in question a Mercarb with 1 idle mixture screw or a Rochester with 2 idle mixture screws? Also does it have a nipple where the clear hose connects to the air horn?
  13. K

    74 stringer electric shift rebuild

    Looks good, the only thing left to check is the propeller, and voltage to the drive on your next time in the water.
  14. K

    Upper Gear Case Bearing was Destroyed Sterndrive. Need help with part # Merc Alpha One Gen One.

    It may be possible that the upper bearing could be friction welded to the stub shaft. While the housing could be salvaged it takes a set of shimming tools along with a hydraulic press. I repaired many like that before the SEI drives became available If the case was not damaged. Your best option...
  15. K

    74 stringer electric shift rebuild

    Did you replace the shift cable wire? Also you need to be sure that a full 12 volts is going to the drive. Use a jumper wire from the battery to the forward “green” wire just to be sure that is not the cause. The only other fluid that OMC approved was automatic transmission fluid if type “C”...
  16. K

    74 stringer electric shift rebuild

    Did you use gear oil made for electric shift lower units? It does however may be the propeller hub. I must congratulate you on your work that you have done so far to the “basket case” and finally got it going.
  17. K

    Strange engine sound need help

    It looks like the pulley on the raw water pump has a build up of rust. That can cause belt failure. It can be cleaned with wire wheel on a drill or take it off then have it glass bead blasted and powder coated.
  18. K

    Strange engine sound need help

    I agree that it appears to be belt related. They are not supposed to walk back and forth in the pulleys. Is that the original belt?
  19. K

    Pressure/Vacuum Test Lower Unit Sterndrive Merc Alpha One Gen One.

    The main purpose of the lower seal is to protect the upper seal. Once the lower leaks the lower end of the driven gear will rust which causes the leak. If you can, try to pressure the upper case, I am pretty sure it will not hold pressure. The bottom line is you will have to take the upper...
  20. K

    water in engine, is it salvageable?

    What year is your boat? Something to also consider whichever route you take, be sure to replace the thermostat and the water pump in the drive.
View older results
Top