Search results

  1. K

    2.5L Mercruiser Rubber Beveled Seal/Guide found in Oil Pan

    That is a sealing grommet that seals one of the bolts which mounts the lifter gallery cover.
  2. K

    1988 TRANSOM REMOVAL

    Pull the engine, unbolt the “Y” pipe disconnect the steering. The shield should come off after the rest of the hardware is removed.
  3. K

    1988 TRANSOM REMOVAL

    What is the reason that the transom shield has to be removed?
  4. K

    1988 TRANSOM REMOVAL

    Is the drive removed from the transom shield? With the engine removed and the power trim motor wires disconnected remove the bolts that mount the “Y” pipe. You might be able to leave the hydraulic trim hoses connected to the trim pump and it will come out with the transom shield. Remove the...
  5. K

    1988 TRANSOM REMOVAL

    As Bondo said which engine? 4 cyl 6cyl or V8, 270,280 or 290 drive, manual tilt or hydraulic trim manual or power steering? Try to post some pictures.
  6. K

    Is my coupler off ? looks like it and drive won't go back in ..

    In case there is no more down adjustment take the front mount to a welding shop and have 1” cut out.
  7. K

    0mc 800 outdrive tilt gear adjustment

    That is a good point Redrig, you just never know what has been left off the last time someone fooled with it.
  8. K

    Water coming into bilge

    Another possibility could be the rubber ring that seals the upper driveshaft housing to the inside of the bell housing. If the ring was not glued in or was pulled down when the drive was installed.
  9. K

    0mc 800 outdrive tilt gear adjustment

    Where the quadrant gear is mounted on the upper gear case does it look like that area is cracked or has been welded ? Can the small gear be moved up and down as if the housing is worn where the shaft comes through?
  10. K

    0mc 800 outdrive tilt gear adjustment

    Are you sure that the tilt motor is getting enough current to operate?
  11. K

    Uppercase on 235 stringer locked up..

    Pull the shift cable out through the upper gear case then remove the bolts that mount the top cover now you will be able to pull the upper from the lower section. Have you checked the oil in the lower gear case to see if it has water in it? Hopefully the oil is clean. Sometimes just the...
  12. K

    Marine Flywheel compared to an auto flywheel

    One other thing, be sure to replace the starter drive since it may have caused your problem. Be sure to get a new one and not one that was rebuilt.
  13. K

    Marine Flywheel compared to an auto flywheel

    The ring gear is replaceable. NAPA stocks the ring gear, just count the teeth. It is easy to knock the damaged one off with a brass drift and a suitable hammer. You heat the replacement in your stove and it will drop on and shrink itself out tighten up.
  14. K

    Droping a 302 in my boat

    What horse power was the original engine? 170 or 190
  15. K

    1975 starcraft chieftain tilt mechanism and bellows

    Those Sealocs are the current day replacement for the outhouse version of the old Sears & Roebuck catalogs.
  16. K

    1975 starcraft chieftain tilt mechanism and bellows

    It could be a Ford 351, does it have hydraulic engine mounts? Contact Crowley Marine for parts and get a Genuine OMC service manual. You will be going to need it.
  17. K

    OMC 800 Tilt - Need help!

    If the Tilt shaft has not been removed then the thrust washer should still be in place. I have had those fuses look good and show continuity but not be able to run the tilt motor.
  18. K

    OMC 800 Tilt - Need help!

    Remove the tilt motor and the hammer blow coupling, there should be a plastic thrust washer on both sides of the coupling to keep it centered and not drag against the housing. They can be substituted with a thin steel washer with a little grease if you do not have the plastic ones. If the tilt...
  19. K

    MC-1 Gearbox

    Sometimes when the gears go out they flare out to the point where they cut into the water jacket or you cannot get them out because of the groove that is cut into the case. You are better off looking for a replacement either used or new from SEI.
  20. K

    1885 5.7L weak water supply to circulation pump

    There is one passage to check out in the thermostat housing. There is a metered hole which is the by-pass for when the thermostat is closed. I think it is around 5/16”-3/8” . One other easy test to check for an internal pressure leak from the drive is by starting the engine and at idle with...
Top