Search results

  1. K

    Slow crank

    To set the dwell I do it with the plugs out and the coil wire grounded. I also like to set the timing with the spark plugs on the wires but grounded on the manifold. That way you do not have to keep starting the engine.
  2. K

    350 MAG MPI Reman maybe Gen II??

    Before you start get the tool that releases the fuel line from the rail. Hopefully you have compressed air, blow the rust,dirt out from around the injectors. Remove the throttle body. Remove the electrical connections and squirt some WD40 or similar around the injectors to help them come out...
  3. K

    Mercruiser 3.0L hot issue

    Try replacing the rotor, what you are describing is something that was pretty common around here. It would get so hot it would go to ground. Mercruiser started supplying a rotor that the blade was slightly longer and that worked. Try to get one from Mercruiser or just have a few on board. If...
  4. K

    1977 OMC Stringer running hot or ??

    You just had it over filled, the heat from the sun will make that happen. When the vent hose is filled with gas that will cause a slight positive pressure in the tank.
  5. K

    Gas vapor out the secondaries at WOT

    Does the exhaust exit through the drive or through the transom? How is the compression. Did this symptom happen all at once or gradually? I do not think you have a carburetor problem. Something else is causing the problem.
  6. K

    Question on stern drive re-installation

    2Xs with southkogs on the ball gears. The main thing to watch is accelerated wear which can be caused by forgetting to have the drive in the full down position or distorted housings caused by striking submerged objects.
  7. K

    Help needed on OMC stringer

    2X with Redrig On the water pump & ball gear shaft. When the intermediate shaft is stuck/rusted to the engine coupler you are in a world of hurt. The only way to get it out is to cut a hole in the side of the intermediate and cut the shaft with a cutting torch. Then remove the engine and unbolt...
  8. K

    MC-1 Back Together, Temp 175 Fahrenheit?

    I would pull the lower unit down and make sure the gaskets are mounted on the water pump housing correctly. Are you sure the copper pipe is in the water pump guide tube?
  9. K

    Slow crank

    Take the spark plugs out and see if it turns with the starter.
  10. K

    Hard to start unless starter solenoid is shorted

    Do you have a points ignition or the later Mercruiser electronic?
  11. K

    1970 Johnson SeaSport II

    Check your private messages, I sent you some advice.
  12. K

    1970 Johnson SeaSport II

    I just checked with Crowley Marine. They have the most critical part, the pinion shaft that has a sealing surface #0382883. They do not show the water pump shaft but if the splines are still good it can be reused. The seals also are available even Sierra marine has them. The Sierra # is...
  13. K

    1970 Johnson SeaSport II

    What year is the boat? If it is after 1968 the parts are not a problem. Most probably the lower pinion housing seals, pinion shaft, water pump shaft and of course the water pump should be replaced. The 16c model came out in 68, previous model was a 15s.
  14. K

    Volvo Penta SX-C NO GEARS sheared something

    With the engine out of the way it will be easier to drive the gimbal bearing out from the inside. A large punch with a suitable b F h.
  15. K

    Push Rod Cover Oil Leak

    An old mechanic‘s trick. Back the bolt out about 1-2 turns, wrap the underside of the bolt head with kite string then tighten.
  16. K

    3.7 mercruiser

    Pull the valve cover and and check for a loose rocker arm, you will have to bump it over to check them all. Hopefully you do not have a worn out cam lobe caused by the lubricants that do not have the zink additive.
  17. K

    Inline 6 250, 165hp water in oil

    Pull the valve cover and check that the head is not where the leak is, sometimes that is where water will leak through a pin hole in the casting. I have even seen water come up through a head bolt that was not sealed with #2 Permatex. The other common place is at the base of one of the cylinders...
  18. K

    Impeller Badly Damaged...

    Make sure that the stainless sleeve did not spin in the pump cover.
  19. K

    Mercruiser 165 shift cable bellows

    Before you pull the stainless hinge pins you must first pull the small “nails” out that keep the pins in place. They cannot be drilled out, they have to be pulled. You might have to use heat to remove them. If you shear them off in the gimbal ring you will never be able to keep the hinge...
  20. K

    My boat sank, part II

    There will be water in the tilt motor. Easy to remove, the brush head is at the bottom so you want to open it up to dry out otherwise the springs will rust away. Good luck
Top