Search results

  1. C

    Evinrude 1999 225 Code 44

    see write-up on code 44 on the more newer ETEC EMM
  2. C

    Evinrude 1999 225 Code 44

    see write on EP BP SENSOR on later 2002-2006 FICHT... may help...
  3. C

    Johnson 5hp

    anytime you want to work on oldies the best book around is this one for $20 just download and print locally. save it on ypour PC hard drive. or laptop https://watercraftmanuals.com/outboard/johnson/manuals/johnson-302231.htm dirt cheap 400 page + manual covering all aspects of your...
  4. C

    40hp Johnson blows 20a fuse when key is turned

    hard to tell but the yelllow red is typically the key's START control on the solenoid with the solenoid black being ground... your extra (black-yellow) wire you took off is a ground return supply back to a kill circuit which you disconnected . being a solid ground source is it...
  5. C

    Johnson 5hp

    TN27 like the TN28 also uses the more "modern coils", points and condensers . see Johnson manual page 29
  6. C

    Johnson 40hp 2005 link and idle adjustments

    if it works don't fix it :-)
  7. C

    Johnson 5hp

    yes they will work ... get them while cheap check compression before spending $$$$$ report back findings change plug wires and boots while at it. use 7mm solid strand copper wire local bike shops or small motor shops could sell a few feet to you I have use basic metallic...
  8. C

    2008 etec running rough

    get a PDF copy of the EMM log dump and post it on the ETEC board for expert analysis... tons of codes does not mean much ...codes may be old codes and dated back to 2008 and no longer relevant to your main issue ... INJECTOR code
  9. C

    1967 Evinrude 6 HP (6702) - Newbie

    don't remove it before you find the EXACT sized one ++don't forget to adequately clean the side channel leading fuel to the top idle circuit. blow everything out with compressed air . unscrew the top idle needle a few turns and blow air in the side channel and it should exit the 3...
  10. C

    2008 etec running rough

    depending on inj. type it may be difficult to find one. contact Barnacle Bill. inj codes are... OPEN or SHORTED so inspect wiring before spending big $$$$
  11. C

    1967 Evinrude 6 HP (6702) - Newbie

    agree yet basic concepts and servicing is much similar and the carb itself is very similar to jw carbs and other models. servicing the ignition is identical so for 20$ the knowledge it contains iswell worth it imho.
  12. C

    2008 etec running rough

    could be lots of things and if you plan servicing that ETEC get the EV diagnostic software to help out. https://docs.google.com/document/d/16BAQLd2i43h30MTOuWJ0-T6_DO9wX5yK5MzOOunwzUk/edit A sane EMM can only mess you life if it detects a sensor fault or various specs out of range incl...
  13. C

    1967 Evinrude 6 HP (6702) - Newbie

    that spring just hooks on the small hole under the cam roller and attaches to the side of the engine block. to remove the carb you cand remove the side linkage but take a close up photo for reassembly later on loosen the nusts then unscrew the bolt nuts with your finngers and...
  14. C

    1967 Evinrude Sport 4 60 hp, 60753 A, Configuration Question

    btw I think 5mi/gal should be your target .. my old Merc 500 would pump out about 25 miles on a 5 gal tank at wot... if my memory serves me right. lots of variables here but 2m/g indicates a problem
  15. C

    1972 Evinrude 40 outboard no spark?

    top needle is for idle adjustments.... lower carb bowl has a fixed jet behind the 7/16 nut and all it needs is to be spotless.
  16. C

    Fuel and or oil or mix leaking

    check valve on the recirculation hose is to stop flow back down in the crankcase that oily juice is meant to flow upwards only to the top top bearing VERY old concept back to the 1950's still exists on modern ETEC engines nothing new under the sun :-)
  17. C

    Choke stays closed

    B+ choke power MUST BE via the key CHOKE function for momentary activation at start up. wire it it up correctly and problem solved !!
  18. C

    1971 Evinrude Fastwin Fuel Gremlin

    so the fuel pump is ok you cleaned the carb... but to what extent ?? assuming electricals are ok (good sparks and you have compresseion) idling requires fuel to leave the lower fuel bowl up to the top idle chamber under the dime size plug AFTER the LS needle lets the fuel enter...
  19. C

    Choke stays closed

    the choke is no different from a light bulb.....it works when energized by 12v. and that should be a very momentary thing at start up. if it is permanently fed 12v. back track from the solenoid to the B+ source and tell us what you find.
  20. C

    1998 Johnson 115ELECM vapor pump

    the vapor pump is very similar to common OMC square pumps widely available and kits are also available they work by pulse pressure from the crankcase to pump fuel wheres yours pumps out VST vapors & sends them out the carbs or crankcase to be consumed. the pump innards are...
Top