Search results

  1. C

    J40ELCR WOT needs key pushed and released for full power

    sounds like it needs fuel by choking.. inspect all hoses fuel pick-up filters throttle linkage , air leaks etc... post mdl# and compression #s
  2. C

    1998 Johnson 175 Ficht Not Starting

    I did not read the whole book but I believe that at Key on the start assist circuit (SAC) should immediately get the HPP going giving you some semblance of available PSI,s regardless if the engine strarts or not. that said and you seemed to have sparks ...... fuel injection does not seem...
  3. C

    1973 4hp Evinrude

    well there you go IR heat gun will tell you how and where it is hot assuming you do pump water. this post 43 on a least complex of OB's ... good luck.
  4. C

    power trim stays on 150 2000 johnson

    melting indicates very high current draw across a resistive path P=R Xi Xi bad -flooded switches would likely not carry such high current and likely just blow the 10 amp fuse ... used to energize the low amp relay windings used to mecanically close and feed high current to the...
  5. C

    1973 4hp Evinrude

    these 4hp do run hot ....so what is HOT ?? the exhaust cover is NOT water cooled like bigger HP models and they frequently become discolored. measure the engine PH with a IR heat gun to detect any true HOT spots
  6. C

    1973 4hp Evinrude

    maybe I am wrong but I do not think you need so much sealer on the impeller housing and in any case where would air enter the pump if it is under water ?? these are as simple as they get engine wise.
  7. C

    1973 4hp Evinrude

    millions were made and still run perfectly. nothing realy wrong with the design. if colling flow is a problem on your 4hp then there is blockage somewhere and needs to be found. pull the PH if you have to and flush all passages with a cleaning agent...or just soak passages with hot...
  8. C

    loading up pictures on this site

    I seem to be getting server problems . just me ?
  9. C

    Evinrude 6hp -1985

    these small engines have a strong heritage back to the 50's ...just feed it good fuel, oil, impellers, grease and some car wax :) and they last forever
  10. C

    1998 Johnson 175 Ficht Not Starting

    and fuel pick-up filters etc...including deteriorated fuel hoses ..a high pressure test and lift pump pressuretest will determine if fuel makes it to the VST properly then the injectors then it becomes a . question of proper injector operation if not crudded up , ignition control by the EMM.
  11. C

    1998 Johnson 175 Ficht Not Starting

    EMM does not see everything it only senses things like current flow to some parts, sensor outputs etc... it does not see cracked coils dirty injectors bad fuel flows poor injector pressure etc... having no codes just eliminates a lot of things to check out. before swapping...
  12. C

    Need help with strobe timing on 1972 9.5 HP Johnson 9R72M

    look closer
  13. C

    1987 Johnson VRO70 Model # J70TLCUR Alarm staying on

    is there a vent on the oil tank.. disconnecting the line seems to have rendered the primer bulb soft again ??
  14. C

    1998 Johnson 175 Ficht Not Starting

    could be fuel starvation overheating component vst air lock keeping fuel from entering the VST etc... post your recent EV diagnostic report and... engine model# if ECM-EMM decisions are not causing the shut down due to a critical sensor detected anomaly then you need to check all...
  15. C

    1976 Johnson 70 hp outboard 70EL76D fuel pump help!!!!!

    left side bottom nipple/hose goes to crankcase for a pulse cover hose is fuel IN right nipple is fuel out to carb
  16. C

    Engine dies under a load

    Happy ending... thanks for feedback but....doesn't explain compression #s ???? happy ending nonetheless
  17. C

    1998 Johnson 175 Ficht Not Starting

    you are correct the 1990-2001 does not go up to your engine size but the fundamentals are there. As to the other link it also contains basic info. your engine has the infamous PDP known for cold solder joints on the main B+ entry into the panel. not saying it is the problem mind you just...
  18. C

    Engine dies under a load

    stuff happens when you work with one eye missing :-)
  19. C

    How many of us have a GREEN Seahorse motor ?

    got me a TN27 I refurbished carb...impeller etc...nice standard ignition.....sitting -sleeping in the shed.
  20. C

    Engine dies under a load

    close to 37,000 feedbacks should not be ignored very odd....did you or not try another compression meter or pull the head to look inside. gaskets are cheap and you have no other options. btw ... "Hello have a 1984 Johnson 150 V6" is this a new to you engine ?? with untested...
Top