Search results

  1. alldodge

    changing navington light on 19 ft./ 2007 bennington pontoon

    I would say the light has been glued, can use something like a putty knife to get under it. I would also say that most likely the green lens is just snapped onto the black base. Might crack the lens but should make it easier if a hair dryer or heat gun is used Have you thought about replacing...
  2. alldodge

    1978 Mercruiser 228 Sterndrive help

    Welcome As others mentioned, just get a new SEI drive, as 1.47 ratio. It most likely can be rebuilt but its not just the cost for parts, its also the cost of the special tools you will need. The boat being a 1978 and in salt, do look at the transom real close, there may be some rot
  3. alldodge

    Zenith 263M2 Carb Float Setting

    Welcome Found instruction sheet at Mikes Carb https://www.carburetor-parts.com/assets/instructionsheets/K5009.pdf
  4. alldodge

    changing navington light on 19 ft./ 2007 bennington pontoon

    Welcome Going to need a bit more info then that. Post a pic so we can see what kind of light it is
  5. alldodge

    Mercruiser trim stuck in up position

    Read our rules, do not post in threads more then 90 days old Closed
  6. alldodge

    mercruiser 4.3 thermostat housing

    These are correct for the inner clips These are my notes 1-6301DL Autozone (Alpha) 805536A2 permalube – Sierra 18-2097 Greaseable older Merc 75831T1 , GLM 8030 at Mercstuff, Sierra 18-2174
  7. alldodge

    mercruiser 4.3 thermostat housing

    Yes they do 18-5274 Summits search function its very good. Easiest way to find these kinds of parts, is search the web and find the part. Then go to Summit and enter the part number
  8. alldodge

    mercruiser 4.3 thermostat housing

    I would get a new cap and rotor
  9. alldodge

    mercruiser 4.3 thermostat housing

    8810 fits TB 4 and 5 along with EST and has all 90* (pic) plug boots 8835 fits EST (most likely also TB) and has mix of 90* and 45* plug boots IMO they will both fit
  10. alldodge

    Looking for any suggestions

    ok I'll take it that there is a misprint of .04 to .4 but your just spitting out what it shows in the book and for me that's not helping. The TPS volts should vary based on what the IAC and MAP sends to the ECM. It won't just stay there. I'm now wonder what else has just been said
  11. alldodge

    Looking for any suggestions

    So the reading at idle is .04V and you watched as rpm's went to WOT and it was 4.92V ?
  12. alldodge

    Looking for any suggestions

    The injector place says they have new and "rebuilt", it would have to be brand new. Have you looked at the spray pattern with a timing like as suggested? Want to see what the reading is at idle, not what it does with key on and motor not running.
  13. alldodge

    Looking for any suggestions

    Where did you get the new injectors? With scanner in place what does the TPS and IAC show when idling?
  14. alldodge

    Winterize Engine That Won't Start

    No, no, no, no it does not mean that. Water fills the block weather the thermostat opens or not Pull block plugs (one each side), exhaust (each side), oil cooler and then your good
  15. alldodge

    Winter mice are too much this cold winter in New Jersey.

    Well I've caught and killed 9 in short order, so maybe they are dumb here
  16. alldodge

    mercruiser 4.3 thermostat housing

    They are marine so will be long enough, the question is do you have Delco EST or TBV distributor? I'm pretty sure they both use the same wires, but not positive
  17. alldodge

    Winter mice are too much this cold winter in New Jersey.

    Have caught several mice with a 5 gal bucket Put a small amount of food (bird, dog, cat) in bucket. Place bucket next to something they can climb. Next day or two use 2x4 to crush mice, dump and repeat
  18. alldodge

    Mercruiser coupler runout

    Welcome ItestBoats Please read our rules about old threads. Do not post in any over 90 days old since last post unless you started the thread Closed
  19. alldodge

    Mercruiser 496 MAG Refresh Thread

    If the motor has the round 10 pin plug then yes it can be run on the stand the same way
  20. alldodge

    Need Help & Advice on a Purchase....

    Interiors are great but the motors appear to just have regular maintenance done. Your comment Looks like the Crown has seen more then a few, might have even lived in it, and in that case I'm leaning to pass
Top