Search results

  1. JASinIL2006

    How to video cavitation plate on the water

    GoPro? Cell phone on a (long) selfie stick?
  2. JASinIL2006

    new to me 97 ski sanger dlx 20 stringer movement near stern

    I personally wouldn't use the boat and I wouldn't take anyone out on the boat, unless they signed a liability waiver. If your stringer is that bad, who knows what other structure is compromised?
  3. JASinIL2006

    Trailer Brakes

    I have a very hard time believing the “I phone folks” would accept a manufacturer with an 80% failure rate. That is not believable.
  4. JASinIL2006

    Trailer guides with step in the way

    Poles are OK if you just need a visual indicator of where the back of the trailer is. They don’t work very well as bumpers to help guide the boat onto the trailer in windy or heavy current conditions; they bend pretty easily if the boat whacks into them. If you’re looking for something to help...
  5. JASinIL2006

    Pet surgery cost😮

    I’ve seen this recommended by vets to help choose pet insurance: https://www.pawlicy.com/
  6. JASinIL2006

    Dock question: how do these sections hook together?

    Actually, the more I think about it... if that's not a floating dock, it might be that those hooks are really all that hold the sections together.
  7. JASinIL2006

    Dock question: how do these sections hook together?

    It looks like once the sections were joined together using that hook thingy, that you could reach the holes (by standing beside the dock) that are adjacent to the hooks to attach the sections more securely using whatever hardware one uses with that kind of dock.
  8. JASinIL2006

    Dock question: how do these sections hook together?

    Does that hole next to the witness mark serve any purpose? I'm wondering if the sections get loosely bolted together. It seems that if the dock is held together only with that angled hook section, a bit of rough water could easily cause the sections to separate.
  9. JASinIL2006

    Awfull time launch & retrieve roller trailer

    Spray silicone might have the same effect with less environmental impact.
  10. JASinIL2006

    Any Transom experts here. I have a Transom Rebuilding Question.

    I have one of those for my table saw. They work great.
  11. JASinIL2006

    Any Transom experts here. I have a Transom Rebuilding Question.

    Personally, I'd just slap some PB in there with a 3" putty knife and then smooth the fillet using a large spoon. (Buy one at the Dollar Store.) I suppose a caulking tube would work, but that sounds like a messy pain in the behind to me. One helpful tip for smoothing fillets: after you have...
  12. JASinIL2006

    Any Transom experts here. I have a Transom Rebuilding Question.

    It's a bit late, but the things you want to make sure are: 1. Thickness of transom (transom core + fiberglass + peanut butter) is between 2" and 2.25" 2. The exterior of the transom (where the gimbal housing meets the exterior of the hull) is perfectly flat top to bottom and side to side. 3...
  13. JASinIL2006

    Any Transom experts here. I have a Transom Rebuilding Question.

    I used a small heater to keep temps above 70. Cooler temps will definitely affect curing time.
  14. JASinIL2006

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    I know I used at least 20 gallons of resin, and I didn't have to do my stringers.
  15. JASinIL2006

    Thru hull

    MarineTex (or PC11) or 4200. I would never use silivone.
  16. JASinIL2006

    dash cams

    This may have more features than you need, but it is very highly recommended on a truck forum I frequent. https://a.co/d/jjIJKss
  17. JASinIL2006

    Question/Advice: Fiberglass over old Fiberglass In Bilge Area.

    You can sand, but it will take a long time... I'd start with 40 or 60 grit paper on an orbital sander. You can get a 4.5" corded grinder from Harbor Freight for about $15. That would save you a whole lot of time...
  18. JASinIL2006

    New canvas bow cover rolling at edges, solutions?

    It’s easy to add snaps to both the boat and the cover. That’s where I’d start.
  19. JASinIL2006

    Any Transom experts here. I have a Transom Rebuilding Question.

    I took the screws out because I didn't want to take a chance on drilling into a screw if I had to install any kind of thru-hull fitting. I filled the holes with thickened resin before I skinned the transom core with fiberglass. For applying the peanut butter, I used a large (4" or 6") plastic...
  20. JASinIL2006

    Kicker on a CC?

    I don't like the emissions of the old 2 stroke engines, but we have a 4 hp 2-stroke outboard, a 9.9 2-stroke outboard and a 9.9 4-stroke Mercury outboard. I would trade the finickiness of the Mercury 4-stroke in a minute for a simple, reliable 2-stroke. Maybe we have a lemon, but we never know...
Top