Search results

  1. JASinIL2006

    Are wheel locks the way to go?

    Honestly, I think they offer about the same level of security. You could buy a coupler lock like in post #5 and a couple Oxgord Trailer Wheel Locks (I didn't see them iBoats, but you can get them on Amazon for about $40 each) and be all in for less than $120. Probably more peace of mind than...
  2. JASinIL2006

    No core floor

    The stringers on my boat were made with foam cores and thick fiberglass walls. I'd guess the fiberglass was 1/4"-3/8" thick and they are extremely rigid. I'd start by planning on 3/8" thick and then adding a layer or two if you have any bounce/flex. I don't recall ever seeing a guide that...
  3. JASinIL2006

    Marine grade wood sealer advice

    If the wood still looked thirsty, I'd probably hit it with a second coat of Old Timer's.
  4. JASinIL2006

    Marine grade wood sealer advice

  5. JASinIL2006

    Are wheel locks the way to go?

    Did they steal his truck, too? I just have a lock that inserts into the coupler (the one linked below, actually) if I'm leaving the trailer unattended. It won't stop someone who really wants to steal it, but it will discourage a more casual thief...
  6. JASinIL2006

    Stingray 208 water in the engine room

    If I were in your position, I'd strongly consider getting a second battery and wiring the bilge pump directly to that additional battery. It would make me very nervous to have a boat slipped without an operational bilge pump.
  7. JASinIL2006

    Stingray 208 water in the engine room

    Is that the amount of water left after your bilge pump has run?
  8. JASinIL2006

    Stingray 208 water in the engine room

    Do you keep your boat covered? How much water is getting into the bilge when it rains?
  9. JASinIL2006

    Has anyone used a automatic charging relay?

    Actually, using both is a good idea. If you buy the BlueSea Add-A-Battery kit, you get the best of both worlds: an ACR (to automatically charge both batteries) and a selector switch.
  10. JASinIL2006

    Water in my bilge

    So, while the boat was running for 8 hours, there was no leak, but after it sat in the slip for another 8 hours, you found water in the bilge? Is that correct? Also, I agree with others that filling the bilge with water is a bad idea; you're unlikely to find the source of your water and you'll...
  11. JASinIL2006

    Adding 2nd battery?

    You don’t want a 50+ pound battery flying around yhe boat if things get rough. Strapping one battery to another sounds like a particularly bad idea. Just make sure any screws you put into the boat are sealed well and you should be OK.
  12. JASinIL2006

    1979 Glastron Carlson CV-23 restoration

    Agreed. Marine plywood is overpriced and not needed.
  13. JASinIL2006

    Water in bilge? Bilge pump runs too often.

    Bellows are too critical (and too much of a pain to install) to cheap out on aftermarket parts. Do yourself a favor and stick with Quicksilver/Mercruiser.
  14. JASinIL2006

    Towing and Cockpit cover concerns?

    Ignoring for a moment the possibility of snaps coming unsnapped and your mooring cover blowing off while on the highway, there is no way I want to subject my expensive cover to getting battered around in the wind at highway speeds. I don’t believe those covers are designed for that kind of wear...
  15. JASinIL2006

    Towing and Cockpit cover concerns?

    Agree.
  16. JASinIL2006

    New owner

    I bet the fuel tank is under that panel.
  17. JASinIL2006

    Ideal tongue weight?

    I belong to an active F150 forum where towing is a hot topic. The consensus seems to be that while it's not a problem for boat trailers to have a tongue weight of 10-15% (the commonly cited figure, esp. for travel trailers), it's generally OK for boat trailers to have less tongue weight, in the...
  18. JASinIL2006

    Rotten 1982 Beachcraft

    Nice work! It IS pretty amazing how shoddily some of these boats were built originally. When finished, yours truly is going to be better than new.
  19. JASinIL2006

    Suggestions for fiberglass repair along the keel

    This ^. I'd get some gelcoat paste, fill the gouged area, then add a Keelguard.
  20. JASinIL2006

    Treated bunk + carpet + aluminum = CORROSION

    I'd be getting rid of the PT wood. I wouldn't want that anywhere near pontoon logs.
Top