Search results

  1. stresspoint

    4.3 Rear Main Seal replacement 2007 Tahoe Q7I Sport Fish

    looking on you tube that motor should come out reasonably easy , the hull has a recess to allow the motor to almost lift strait up. with a bit of wiggling and spinning it should come up with a over head gantry without much disassembly.
  2. stresspoint

    Power Boat sinks in Michigan

    most likely one of those twin inboard go fast boats that un qualified people are converting to quad or triple outboards , IMO , never a good outcome, impressive for sitting at dockside restaurants and sandbars, that's about it.
  3. stresspoint

    98 seedoo GTX issues

    how did you clean the TB ?. check voltage out put when running then check again as you ease on the throttle , if voltage drops or spikes intermittently then the regulator/rectifier is damaged.(possibly ECU). running or trying to run to often like this will fry the ECU , that you don't want $$$...
  4. stresspoint

    4.3 Rear Main Seal replacement 2007 Tahoe Q7I Sport Fish

    engine crane with extension boom and counterweight , strip as much of the motor as you feel comfortable to make it smaller and lighter. i have a semi complete V8 engine on a frame that sits snug on my crane base to counter weight the boom extension. TIP; move the trailer and boat rather than...
  5. stresspoint

    Alpha one shift adjustment

    when i replaced the lower cable on my alpha 1 gen 2 i had problems picking up reverse with the book settings ,i winged it and its been working fine since . as posted if its working leave it .
  6. stresspoint

    Who here would buy a boat with 1400hours on a 454 mpi?

    my mate sprayed / drowned his painted steel trailer in some fish oil stuff , that thing is probably still like new and that was 15 or so years ago used in salt water ,left wet , and no care taken not to scratch it. trim and stuff is personal choice , i tidied up the trim in my Maxum as it was...
  7. stresspoint

    2013 Volvo Penta 4.3GL Oil Pressure Drop & Valve Tapping / Rattle

    if i had to take a couple of guesses , i would say the oil filter you are using is a dud. second guess is the check valve in the oil pump sticking.
  8. stresspoint

    Who here would buy a boat with 1400hours on a 454 mpi?

    that motor properly maintained and being that it was fresh water used @ a low 1400 hours will have lots more useable life even if you run it in salt water ,let the kids thrash it and put it away wet. IMO it should not be a concern , as Scott Danforth posted :treat it , get some closed cooling...
  9. stresspoint

    Strange ticking rattling on 4.3 V6

    year of motor ? , possibly a hydraulic lifter not quite up to par. if non adjustable it will need replacing or just live with it. if however you have an adjustable lifter motor you may get away with a valve lash adjustment.
  10. stresspoint

    How to clean Flywheel taper

    i usually wipe the taper with solvent , inspect the condition iE: deep scoring etc, if all looks good i get a fine emery strip and lightly scuff the surface of both the crank and FW. then i put some valve lapping past on the taper and spin it a few 1/8 turns back and forth with light pressure ...
  11. stresspoint

    Evinrude Mariner 6 HP 1965 Model 6502, 6503 3 fin prop

    ok , I'm interested , i have a later ,i think 1995 long shaft Evinrude with a dead power head sitting up there too.my 7.5 is short shaft BTW. :) what's the secret ????
  12. stresspoint

    Mercuiser 357 mag low compression on #6 (120 psi)

    h a ha , that bloke that did the inspection needs to learn his job ( or do something else (y)) sounds as if one of the cylinders was correctly checked and the others were guessed. even an excessive carbon build up will not give those sort of readings. grab yourself a cheapo gauge and recheck...
  13. stresspoint

    Hi I need alittle help

    the solar reactors generator is on its way out :). seriously , you need to give more information , motor serial # or type . did it just break down or did it sit and just not work when you went to start . ? what checks have you already done. the more info the easier it is for you to get help...
  14. stresspoint

    Evinrude Mariner 6 HP 1965 Model 6502, 6503 3 fin prop

    ah this post brings back memorys of a 7.5 i still have up the shed that has no prop ," never could find the correct one for it", perfectly good motor , prop got destroyed along with the sheer pin, plastic screw on. FWIW OP , there is no other prop that fits , those earlier motors seemed to have...
  15. stresspoint

    Exhaust flapper fell down in the exhaust tube

    i use bits of mig welding wire for all sorts of things , maybe run a couple of feet and bend a hook on the end ? .
  16. stresspoint

    Ignition shift interrup on 1980 V8 Mercruser inboard

    the switch is also always open, when pushed in its closed , IE: when you push the lever forward it activates.. easier explanation (insert head scratch meme here) it works opposite to a normal momentary switch
  17. stresspoint

    Exhaust flapper fell down in the exhaust tube

    ha ha, funny thing , when i had my motor out and exhaust flappers removed for replacement , i had this thought , i hope nothing falls down there "ill never get it out once the motor is in". with that thought i taped up the Y pipe so it was sealed , that tape stayed there till the flappers were...
  18. stresspoint

    Exhaust flapper fell down in the exhaust tube

    i see a Y pipe removal in your future !!!!!..
  19. stresspoint

    Hot rod/mods

    not a lot of love for hotting up 4 stroke outboards , i don't know why but people don't know what they are missing out on they are killer when work is done
  20. stresspoint

    Hot rod/mods

    latest boat Maxum SR 1800 4.3 vortec , they said you cant make power with a 4.3 , well that theory was wrong , we hot rodded it and its happy to cruise @5500 rpm , will touch on 6000 if i let it. Stevens TR2 center mount , toy boat , 500+ hp 5.7 , was Vdrive converted to center mount , loud...
Top