Search results

  1. Scott Danforth

    Mercruiser dies after getting on temp

    something not right. should be ~8-9 volts when engine running at the coil, and battery voltage when cranking make sure to get a points file (or use one of your wifes emery boards) and a dwell meter along with the feeler gauges. the points file is to dress the contacts, the feeler gauges are...
  2. Scott Danforth

    Aftermarket fuel pump recommendations

    do a google search for the forums. you can just replace the airtex pumps in the fuel pump assembly. about $200
  3. Scott Danforth

    Engine, Carb or Prop? need suggestions or ideas please.

    The coupler for a stringer does not care about the flywheel, only the crank pattern The only Stringer coupler for GM motors only fits the 1985 and older 2-piece RMS cranks
  4. Scott Danforth

    Engine, Carb or Prop? need suggestions or ideas please.

    There is no 2-piece RMS button coupler for a stringer 800 that I have found , and the 1-piecs RMS pattern is different. The bolt circle on the 2 piece rear main seal crank is 3.58" while the 1 piece is 3.00" bolt circle The Ford pattern is close to the 1-piece.... however with one hole rotated...
  5. Scott Danforth

    Engine, Carb or Prop? need suggestions or ideas please.

    how did you mate up a 4.3 to the stringer drive? only the 1985 4.3 has the right crank (2-piece RMS) to mate up to the OMC button coupling unless you had a button coupling custom made are you sure the motor is not the 3.8 liter? with your boat being a 1984, the 4.3 didnt exist yet. the 1985...
  6. Scott Danforth

    1998 5.7 Freshwater cooling kit info

    this should be the connections for the VP half system (going off of memory from 2008). reach out to your local dealer with the engine serial number and they can get you the correct diagram.
  7. Scott Danforth

    Let's talk skill...

    first, what is your idle speed? should be 650 RPM in gear at idle.
  8. Scott Danforth

    Keep blowing my starter solenoid up.

    got a picture of the wiring to your pilot relay? pretty sure the wiring needs some TLC.
  9. Scott Danforth

    1998 5.7 Freshwater cooling kit info

    factory service manual has the plumbing diagram. do you have the deaeration tank?
  10. Scott Danforth

    Lowe '08 20'

    Aftermarket add on for changing room curtain Do you mean gas spring? If you have an outboard, there isn't any. If you have an IO, look at the old one for the part number, length and force Google tongue weight. Plenty there I wouldn't tow with a mooring cover, it will most likely blow up...
  11. Scott Danforth

    Bayliner 175 to 170 conversion

    There have been several I/O to OB conversions on Iboats over the years. Very few completed, non were happy with the results unless they used a pod I agree to sell it and buy what you want. Even if you gave away your current boat, buying an OB boat will be less $ than a conversion
  12. Scott Danforth

    If you're wondering if your anti siphon valve is stuck, or clogged, here's a test....

    All the AS valves have a number on them. That is the vacuum that they open. Make sure you know the number when testing
  13. Scott Danforth

    Possible binnacles and gauges - 2017 Yamaha F150XCA

    You need the boat side harness that goes between
  14. Scott Danforth

    A question for Mercury outboard techs

    I can reach out to a few engineers I still know at Merc this coming week. However the 600hp motor is a variant of the LS motor and the I/Os of Mercruiser are a variant of the SBC, but the fuel system and storage requirements would be the same They do have different engineering teams, and they...
  15. Scott Danforth

    Float bags for small bow boats?

    Just use foam
  16. Scott Danforth

    2014 GMC Sierra AC

    Huh?
  17. Scott Danforth

    Trailer bearing blowout. Need help with repair(s)

    I use sturdy built trailer (they have a local store)
  18. Scott Danforth

    2014 GMC Sierra AC

    You will need a UV light and the special glasses. I got mine from an auto store about 30 years ago, Amazon has them for about $10
  19. Scott Danforth

    1962 Chris Craft Holiday 20’ bucket list resto

    Speedy recovery Sam
  20. Scott Danforth

    Trailer bearing blowout. Need help with repair(s)

    I just checked prices at my local trailer place's web site. $317 for a pinched axle and hubs
View older results
Top