Search results

  1. Scott06

    Marine Tex on Alodine?

    Do Some research on automotive finishes in many cases it is recommended to put filler over an epoxy or etching primer to prevent metal corrosion. Good primers like this are not weaker. As with everything using the correct materials and prep is key.
  2. Scott06

    Can the base of engine work? Two to bolts under engine are rusted and can

    Then you are doing something wrong. Bellows should last years
  3. Scott06

    prop question

    I ran a 21” pitch but That doesn’t matter as our boats are different
  4. Scott06

    prop question

    My trial with a high five I thought it was junk got on plane fast refs went way up boat went no where. Took it out twice and sold it Much better water sports performance with revolution 4 and Vensura/offshore
  5. Scott06

    Marine Tex on Alodine?

    JB will stick to primer
  6. Scott06

    prop question

    if you are new to it and can't try before you buy then cut your teeth playing with aluminum props. I would think you can get yours repaired for about half of new cost. Properly repaired it will be good as new. If you go to the newer torq flo hub then I think you will need a different thrust...
  7. Scott06

    Can the base of engine work? Two to bolts under engine are rusted and can

    If you had leaking bellows yes replace the gimbal bearing while you are in there They do not like water
  8. Scott06

    MerCruiser update

    Exactly belt and suspenders, plus it only offers more opportunity to sell more services. Not sure on the corrosion. Bottom line if you have a way of doing it that works for you stay with it. I drain , put the plugs back in backfill with a little AF to get any remaining water or water and...
  9. Scott06

    Can the base of engine work? Two to bolts under engine are rusted and can

    there is nothing to maintain on the sealed bearing - only to make sure water stays out . If it is not smooth then replace it
  10. Scott06

    Can the base of engine work? Two to bolts under engine are rusted and can

    yes Quicksilver is OEM and the bearing will be sealed. Should have come with a pipe plug to replace the grease nipple in the transom housing Quicksilver is same parts as Mercury/Mercruiser , just different branding so they can sell them outside of their dealer network.
  11. Scott06

    prop question

    if the laser has more cup or blade area then yes you would want to go down in pitch to stay at same rpm or improve hole shot. As mentioned very much a trial and error thing, since you are new to this might be better to spend a little more to work with a prop shop or marina/dealer who will let...
  12. Scott06

    Can the base of engine work? Two to bolts under engine are rusted and can

    If it is an OEM mercruiser bearing it will be sealed. Otherwise depends on what you bought
  13. Scott06

    SeaDoo Tow Tap

    I believe 6 knots is the Mendoza line where valve is needed
  14. Scott06

    350 mag guardian thinks engine is running hot but gauge show good.

    First would verify that the temp gauge is accurate with a IR gun on the thermostat housing. If it is not actually overheating likely issue is temperature sensor on port side of thermostat housing. If that was giving wrong temp indication to ECU that would likely cause what you are seeing.
  15. Scott06

    Hard plane after switch from points ignition

    Cannot be worse than a blown up engine .... seriously if you set it how you outline above you will be ok as you are setting to factory spec.
  16. Scott06

    prop question

    Depends on how you use your boat. If top speed is your thing yes you don't want a 4 blade. If taking 6-7 people in you boat and going skiing or wakeboarding is then 4 blade can be an improvement in holeshot, stern lift and planning speed. If you have a beamy stern heavy boat like mine I get...
  17. Scott06

    SeaDoo Tow Tap

    yes seems like any of them need it. I believe it is just a valve to shut off cooling water supply https://jettech.com/en-us/blogs/news/what-is-a-jet-ski-tow-tap-and-why-do-i-need-one
  18. Scott06

    Trailer axle capacity/sizing

    Agreed my 3500 listed dry weight boat is on a 5200 lb dual axle aluminum trailer. I would not want to go any smaller.
  19. Scott06

    prop question

    That is the best approach. Get wot rpm numbers with what you have. Likely going to a 19 three blade or an 18” 4 blade will give the results you want with out over revving on wot rpm. I had good luck in similar circumstances with michigan vortex 4 blades. Relatively cheap with good results
  20. Scott06

    Gimbal Housing Studs for a Mercruiser Alpha 1 Gen 1. Need the specific part # or size for these.

    Edit posted to wrong thread…
Top